- ページ 2
コントローラー Auber Instruments TH220AのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Auber Instruments TH220A 5 ページ。 Temperature and humidity controller
ページを印刷する
AUBER INSTRUMENTS
The user should decide the appropriate configuration for each output socket
based on the user's particular application. Please refer to section 4.5 and
second 5 for details.
4.4 Change the Setpoints
The setpoint for temperature is TSP (TSP) and the setpoint for humidity is
HSP (HSP). To access the setpoints, simply short-press the SET key, and
then the top window will show TSP and the bottom window will show its value.
Use UP or DOWN arrow keys to adjust the value, and short-press the SET key
again to save the new value and go to the HSP setting. The way to adjust and
save the setting is the same as for temperature setpoint. Once you press the
SET key again, the controller will return to its normal operation mode. Please
see Figure 2 for how to access the setpoints.
Normal
Operating
Mode
72.0
SET
Temp
50.5
Short-press
RH
Figure 2. How to access setpoints.
4.5 Adjust Parameters
Other control parameters are grouped into three sub-menus: temperature
(tE), humidity (Hu), and system (SYS)*. To access these parameters, long-
press SET key for 3 seconds, the top window will show EDT (EDT). Then use
UP or DOWN arrow key to select the sub-menu item (tE, Hu, or SYS) in the
bottom window, then press SET key again to confirm the selection. Please see
Figure 3 for how to access these parameters. The details for each parameter
are explained in section 5.
Temp
EDT
Temp
Temp
SYS
RH
short-press
SET
to co nfirm
Go th rough a ll pa ramete rs in
Go th rough a ll pa ramete rs in
syst em menu
Temp
Figure 3. How to access parameter menus.
2019-05
Temperature
Setp oint
TSP
SET
Temp
Temp
75.0
Short-press
RH
RH
SET
Normal Operating Mode
72.0
50.5
RH
Long-press
SET
3 seconds
EDT
EDT
Temp
TE
RH
RH
short-press
SET
SET
to co nfirm
Go th rough a ll pa ramete rs in
temperature m enu
humidity men u
72.0
50.5
RH
Norm al Operating Mode
5. Parameter Settings
All parameters are listed in Table 1. When a parameter is displayed in the top
window, its value is displayed in the bottom window. The user can use the UP
or DOWN arrow key to adjust the value in the bottom window, then press the
SEK key to save the new value and go to the next parameter. If no key is
pressed for 10 seconds, the controller will exit to its normal operating mode.
Table 1. Parameters.
Code
Humidity
tSP
tSP
Setpoint
HSP
HSP
HSP
40.0
Edt
EDT
Sho rt-press
C-F
C-F
tCM
tCM
tdF
TDF
toF
toF
tAH
TAH
tAL
TAL
tAS
TAS
tSF
TSF
HCM
HCM
HdF
HDF
HU
HoF
HoF
short-press
to confirm
HAH
HAH
HAL
HAL
HAS
HAS
HSF
HSF
HdM
2
HDM
HdT
2
hdt
WWW.AUBERINS.COM
Description
Setting Range
Short-press SET Key
-40ºF ~ 176ºF
Temp. Setpoint
-40ºC ~ 80ºC
Humidity Setpoint
0 ~ 99.9% RH
Long-press SEK Key
tE: temperature menu
Edit parameters
Hu: humidity menu
SYS*: system menu
Temp. control settings (tE)
C: Celsius
Temp. Unit
F: Fahrenheit
Ht: heating mode
Temp. Control Mode
CL: cooling mode
Temp. Control
0 ~ 50.0
Differential
Temp. Calibration
-10.0 ~ 10.0
Offset
Temp. High
-40ºF ~ 176ºF
Limit Alarm
-40ºC ~ 80ºC
Temp. Low
-40°F ~ 176ºF
Limit Alarm
-40°C ~ 80ºC
Temp. Anti-short
Cycle Delay (only for
0 ~ 12 min
cooling)
ON: output energized
Temp. Sensor
OFF: output de-
Failure Operation
energized
Humidity control settings (Hu)
Humidity Control
deH: dehumidifying
Mode
H: humidifying
Humidity Control
0% ~ 50.0%
Differential
Humidity Calibration
-10.0% ~ 10.0%
Offset
Humidity High Limit
0% ~ 99.9%
Alarm
Humidity Low Limit
0% ~ 99.9%
Alarm
Humidity Anti-short
Cycle Delay (only for
0 ~ 12 min
dehumidifying)
Humidity Sensor
ON: output energized
Failure
OFF: output de-
Operation
energized
Humidity Output
0, 1, 2
Delay Mode
Humidity Delay
0 ~ 999 min
Timer
Initi
No
al
te
75.0
1
40.0
1
tE
6
F
7
CL
1
3.0
1
0
2
95.0
3
32.0
0
4
OFF
5
H
1
3.0
1
%
0%
2
90.0
%
3
10.0
%
0
4
OFF
5
0
8
5
9
P2/5