- ページ 8

配管製品 damixa 340000000のPDF インストレーション・マニュアルをオンラインで閲覧またはダウンロードできます。damixa 340000000 13 ページ。 Basin mixer, bath/shower mixer with a long spout and shower set, kitchen mixer

ページを印刷する

Basin mixer / kitchen mixer installation

1. Disconnect your water supply system.

2. Connect a fl exible pipe to the mixer.

3. Important! To prevent damage to the fl exible pipe, twist it into the mixer body manually,

do not use any tools or apply extensive force.

4. Attach mixer to a sanitary ware using the supplied fi ttings.

5. Connect the fl exible pipe to water supply system: the right hose to cold water supply, the

left hose — to hot water supply.

6. Before connecting the mixer it is recommended to remove (unscrew) the aerator in order to

prevent its clogging at the fi rst water feed.

7. Start the water supply system with the mixer in «closed» position and make sure that all

connections are tight. Perform additional connections tightening and sealing if necessary.

8. Open hot and cold water supply for a while, then close water supply and re-install (screw in)

the aerator.

Bath/shower mixer with a long spout and shower set and shower

mixer installation

1. Disconnect your water supply system. Screw eccentric reducers into the water supply

system pipes after sealing the threads with sealing material. Select a position of eccentric

reducers to match and comply with the mixer's connections position. The mixer should be

in a horizontal position.

2. Before connecting the mixer it is recommended to remove (unscrew) the aerator in order to

prevent its clogging at the fi rst water feed.

3. Install decorative plates on the eccentric reducers and connect the mixer's body using tools

with soft extensions. Install a spout to a bath/shower mixer with a long spout.

4. Start the water supply system with the mixer in «closed» position and make sure that all

connections are tight. Perform additional connections tightening and sealing if necessary.

5. Open hot and cold water supply for a while, then close water supply and re-install (screw in)

the aerator.

6. For bath/shower mixer with a long spout and shower sets attach shower head to the hose

using insertions. Connect the hose to the shower slot on the mixer body. Install wall bracket

for shower head in a convenient place for you.

Warning!

Mixers can operate normally with the following water supply system specifi cations:

• Operating pressure interval in water mains is 0.5-6.0 atm. (50-620 kPa).

• Pressure diff erence in hot and cold water supply systems can vary up to 10%. If it exceeds this

value, the pressure increase/decrease instruments installation is recommended.

• Maximum allowable hot water temperature: +80С°.

• Install 100-300 μ fi lters to prevent foreign objects (abrasive particles) from getting inside the

item.

RETRO / OBJECT

Conditioning guidelines

Modern sanitary ware, kitchen and shower mixers are manufactured of a wide range

of materials depending on their operational features and design, demanded by the market.

In order to prevent damage to the product while performing its clean-up, consider certain

criteria.

Mixer conditioning agents

Cleaning agents are required for lime deposits removal.

Always observe the following rules during clean-up:

• Never use the agents, containing hydrochloric, formic or acetic acids since they can cause

major damage.

• For the same reason the use of phosphoric acid should be limited.

• Never mix diff erent cleaning agents.

• Do not use abrasive cleaning agents or accessories (e.g. some cleaning powders or

microfi ber sponges).

Mixer conditioning guidelines

Observe cleaning agent manufacturer's guidelines and the following rules on their application:

• Use cleaning agents, if necessary, considering the application guidelines.

• Cleaning agent dosage and time of treatment should be chosen depending on the product

features (do not treat the mixers with cleaning agents longer than necessary).

• Treat mixers regularly to prevent calcifi cation.

• Spray the aerated cleaning agents on cloth or sponge; do not apply them directly on

sanitary ware, since aerosol drops can get into its holes and cause damage.

• Remove chemical agent residues with clean water immediately after treatment.

Important notes

Liquid soap, shampoo or shower gel residues also can cause damage. Carefully wash

sanitary ware with clean water to prevent it. The use of cleaning agents on damaged

areas enlarges the areas of damage.

Our company's warranty does not cover damages, caused by improper handling.