キッチン家電 Conair Ultimate GS7のPDF 使用方法をオンラインで閲覧またはダウンロードできます。Conair Ultimate GS7 2 ページ。 Ultimate fabric steamer
ページを印刷する
IMPORTANT SAFETY
4. Never operate this appliance if it has a
damaged cord or plug, if it is not work-
INSTRUCTIONS
ing properly, or if it has been dropped or
damaged, or dropped into water. Do not
When using electrical appliances, especially
attempt to repair the appliance. Incorrect
when children are present, basic safety pre-
reassembly or repair could cause a risk
cautions should always be taken, including
of fire, electric shock, or injury to persons
the following:
when the appliance is used. Return the
READ ALL INSTRUCTIONS
appliance to an authorized service center
for examination and repair.
BEFORE USING
5. Do not allow cord to contact heated sur-
faces. Do not pull or twist cord. Let appliance
KEEP AWAY FROM
cool completely before putting away. Loop
WATER
cord loosely around appliance when storing.
6. This appliance has a polarized plug (one
DANGER —
Any appliance is electri-
blade is wider than the other). As a safety
feature, this plug will fit in a polarized outlet
cally live even when the switch is off.
only one way. If the plug does not fit fully
To reduce the risk of death by electric shock:
in the outlet, reverse the plug. If it still does
1. Always unplug appliance immediately
not fit, contact a qualified electrician. Do not
after using.
attempt to defeat this safety feature.
2. Do not place or store appliance where it
7. Never drop or insert any object into any
can fall or be pulled into a tub or sink.
opening or hose.
3. Do not place in, or drop into water or other
8. Do not use outdoors or operate where
liquids.
aerosol (spray) products are being used or
4. If an appliance falls into water, unplug it
where oxygen is being administered.
immediately. Do not reach into the water.
9. Do not use an extension cord to operate
WARNING —
appliance.
To reduce the risk of
burns, electrocution, fire, or injury to persons:
10. Surfaces of this appliance may be hot
1. This appliance should never be left
when in use. Do not let heated surfaces
unattended when plugged in.
touch eyes or bare skin.
11. Do not place the steam nozzle directly on
2. This appliance should not be used by, on,
or near children or individuals with certain
any surface or on the appliance power cord
disabilities.
while it is hot or plugged in. Use the stand
provided.
3. Use this appliance only for its intended use
12. Unplug this appliance before filling or
as described in this manual. Do not use attach-
emptying. Do not overfill.
ments not recommended by the manufacturer.
13. While emitting steam, this appliance
FOR HOUSEHOLD USE ONLY
may cause burns if it is used too closely
UNPACKING INSTRUCTIONS
to the skin, scalp or eyes, or if it is used
Place the box on a large, sturdy flat surface.
incorrectly. To reduce the risk of contact
Carefully remove the appliance from the
with hot water emitting from steam vents,
packing material. Keep all plastic bags away
test appliance before each use by holding
from children.
it away from body.
14. Do not operate steamer without properly
STEAMER ASSEMBLY
filling the water tank.
STEP 1 - Assembling the Support Rod
15. Always keep the hose and nozzle
1. The telescopic support rod comes in one
elevated above the water tank.
part: 1 collapsed pole (with plastic connectors
16. Never yank cord to disconnect from outlet;
on it) with one T-nozzle cradle.
instead, grasp plug and pull to disconnect.
Insert the larger metal
17. Burns could occur from touching hot
Fig. a
bottom of the pole into the
metal parts, hot water, or steam. Use care
holder on the unit base
when removing water tank or when you turn
(Fig. a). Twist the metal
a steam appliance upside down – there may
screw on the back of the
be hot water in reservoir.
unit base until it is tight.
18. To reduce likelihood of circuit overload,
do not operate another high wattage appli-
Open the plastic con-
ance on the same circuit.
Fig. b
nectors and extend the
19. If an extension cord is absolutely neces-
telescopic pole. Close the
sary, a 15 ampere rated cord should be used.
plastic connectors so the
Cords rated for less amperage may overheat.
pole locks in place (Fig. b).
Care should be taken to arrange the cord so
that the cord cannot be pulled or tripped over.
Slide the T-nozzle cradle
20. Never pour water directly into reservoir.
onto pole (Fig. c).
Put water in water tank only.
SAVE THESE
Fig. c
INSTRUCTIONS
Connecting the Lint and Bristle Brush
STEP 2 - Attaching the Steamer Hose
Attachments (if model comes with
Insert hose cap into steamer housing and twist
accessories)
clockwise to securely lock hose onto housing.
Removing the Steamer Hose
1. Insert.
2.Turn.
(make sure unit has cooled)
To remove, turn counterclockwise to release.
Turn slowly.
3. Lock.
1. One quarter turn.
2. Push down.
3. Continue to turn
until hose is released.
Hose may be stiff upon removal from box.
Hose will relax after initial use. T-handle will
sit properly on pole support once hose is
relaxed.
OPERATING
GETTING TO KNOW YOUR STEAMER
INSTRUCTIONS
T-handle steam nozzle
with stay-cool handle
BEFORE FILLING THE WATER TANK
and turbo steam jets
Turn the water tank upside down and inspect
T-nozzle cradle
to make sure the valve and spring assembly
are functioning. Place the tank in the reser-
voir and check that it is seated securely. If
Support rod with
built-in hanger
the tank has been stored with water inside, it
hook to hold
may be necessary to remove the water and
several garments
clean the tank. Follow the steps for care and
at once
cleaning.
FILLING THE WATER TANK
(PRIOR TO PLUGGING IN THE APPLIANCE)
Remove the water tank with the handle and
turn upside down. Unscrew the valve cap in
Removable
the center of the base. Fill tank by holding
5-ft. hose
tank under a source of running cold water
until the tank is filled to the desired level. Do
not overfill. Screw the valve cap onto the
water tank and return the tank to the upright
position. Place the water tank onto the base
and make
Removable,
certain it is seated properly in the cavity.
easy-to-fill and
easy-to-clean
DO NOT FILL THE TANK WITH HOT WATER.
water tank with
integrated carry
handle
Casters for rolling
steamer anywhere
Meijer.com
OPERATING THE STEAMER
1. Make sure the ON/OFF switch is in the OFF
position.
2. Make sure all hose connections are secure
and tight.
3. Make sure the rod is fully assembled and the
hose is not twisted or kinked.
4. Plug the steamer cord into a normal electri-
cal outlet.
5. Turn the ON/OFF switch to the ON position.
6. The switch will light to indicate when power
is on.
7. Steam will be produced from the nozzle in
about one minute.
CAUTION:
Hose will be hot when
in use. Avoid prolonged contact.
Built-in
cord wrap
ON/OFF
switch