ポータブル発電機 Concentric 10590のPDF 取扱説明書＆パーツマニュアルをオンラインで閲覧またはダウンロードできます。Concentric 10590 4 ページ。 Ac hydraulic power unit for auto hoists
ページを印刷するConcentric OIPM P/N_________________
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED. PROTECT
YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN
PERSONAL INJURY AND/OR PROPERTY DAMAGE! RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
Description
The Concentric AC hydraulic power unit is specifically designed
for auto hoist applications. However, it may be used for other
intermittent duty applications that utilize the power up - hold -
gravity lower hydraulic circuit. This hydraulic unit must be used
for mounting in a vertical position (motor up/reservoir down) and
is typically mounted on the side of the auto hoist frame. It is pre-
wired with a push button start switch. Additional features include
a load holding check valve, a manual lowering valve with "feather-
ing" capabilities and a 3 gallon capacity reservoir. The adjustable
relief valve is preset at 2200 PSI.
WARNING!
THIS HYDRAULIC UNIT IS SPECIFICALLY DESIGNED FOR
INTERMITTENT DUTY APPLICATIONS. ANY ATTEMPT TO RUN THE
UNIT FOR EXTENDED PERIODS OF TIME MAY CAUSE DAMAGE TO
THE 115/208-230 VAC ELECTRIC MOTOR.
Unpacking
Check unit for any apparent shipping damage. The contents of the
carton will included (1) AC hydraulic power unit and (1) breather
cap and (1) 45º street elbow. If any of these components are miss-
ing or there is any noticeable damage, please contact the office
where the item was purchased.
Specifications
Motor .......................................... 3.5 HP, 115/208-230 volt, 60 Hz., 3450
RPM, T.E.N.V., 56 frame, single phase
Pump........................................... .129 cu. in./rev. displacement, perfor-
mance is 1.9 GPM at 1750 PSI
Valving........................................ Check Valve
Manual release valve
Relief valve factory set at 2200 PSI
Porting ........................................ 9/16-18 SAE outlet/return for single
acting cylinder, 3/8-18 NPT Cylinder
Vent Port
Rotation ..................................... CW looking at drive end of motor
Reservoir .................................... 3 gallon capacity, cylindrical
Accessories ............................... Push button momentary contact start
switch
Mounting ................................... Plumbed for vertical mount.
SHAFT SEAL
P/N 2120120
GOLD GASKET
P/N 2260084
Nominal
Nominal
GPM @
Operating
CIR
3450 RPM
PSI
0.129
1.90
1900
269xxxx
AUTO HOIST POWER UNIT ORDERING DATA
Factory Preset
Relief Valve
Setting
HP
RPM
Volts
2200
3.5
3
115/208-230
OPERATING INSTRUCTIONS & PARTS MANUAL
AC HYDRAULIC POWER UNIT
FOR AUTO HOISTS
MODEL 10590
MOTOR START SWITCH
PUSH TO START-HOLD TO RUN
6.58 O.D.
TO AVOID PREMATURE FAILURE
DO NOT JOG SWITCH
1.50
1.50
4.00
8.98 MAX.
3.5 HP., 115/208-230 VOLT,SINGLE PHASE
60 HZ., 3450 R.P.M., 56 FRAME, T.E.N.V.
5.79
9.44 MAX.
3.50
2.44
3.26
6.53
M
(BLACK)
GND
T1
T2
T3
L2
CUSTOMER
JUMPER
T5
CONNECTION
L1
JUMPER
NORMALLY OPEN
TERMINAL
COMMON TERMINAL
ELECTRICAL SCHEMATIC
2200
PSI
M
.129
HYDRAULIC SCHEMATIC
Load
Dim.
Dim.
PH.
Hz.
Amps
L
W
1
60
35
32.2
8.8
revised 04/25/2013
33.1
2.00 FILL PORT
C L
HOLD
RELEASE
3.0 Gal. Nom. Cap.
1.19
ADJ. RELIEF VALVE
SET @ 2200 PSI
1.31
22.43
2.06
9/16-18 SAE
STRAIGHT THREAD
OUTLET/RETURN PORT
40 MICRON BREATHER
3/8-18 NPT FILL PORT
2.44
T8
T4
GND
L2
(WHITE)
CUSTOMER
CONNECTION
L1
(BLACK)
ELECTRICAL SCHEMATIC
FOR 208-230 VOLTS (REF.)
Dim.
Stock
Northern
H
Number
Number
9.07
1280624
10590
6.58
Figure 1
T2
T3
M
T5
T8
T4
T1
NORMALLY OPEN
TERMINAL
COMMON TERM INAL