- ページ 3
ネットワーク・ルーター 3onedata IAP2600-BW-8A25-2GT-PDP12 48のPDF クイック・インストール・マニュアルをオンラインで閲覧またはダウンロードできます。3onedata IAP2600-BW-8A25-2GT-PDP12 48 5 ページ。 Industrial outdoor 5g wireless router
ページを印刷する【Pole-mounted Device Disassembling】
Step 1
Device power off.
Step 2
Stabilize the device, unscrew the U-shaped derrick
nut and take out the U-shaped derrick screw.
Step 3
Take out the device, disassembling ends.
【Wall Mounting】
Step 1
Use 4 M6 screws to install the clamp board as
shown in the figure below on the device backboard.
Step 2
Align the other clamp board with the hole center
line of the installed clamp board, then place the
support pipe to align the hole center of the two
clamp boards. When the two clamps are docking, it
can choose 15° or 90° installation angle.
Step 3
Pass the M6 long screw through the hole where the
clamp boards are docked and the support pipe, and
tighten the corresponding M6 nut.
Step 4
Pass the M6 screw through the location hole of the
clamp board. The size of location hole of the clamp
board is as shown below.
Step 5
Install the device on the wall and tighten the screw.
Installation ends.
【Wall-mounted Device Disassembling】
Step 1
Power off the device.
Step 2
Hold the device steadily and screw out the screw in
the wall.
Step 3
Take out the device, disassembling ends.
Notice before power on:
Power ON operation: First insert the power supply
terminal block into the device power supply interface,
then plug the power supply plug contact and power on.
Power OFF operation: First, remove the power plug,
then remove the wiring section of terminal block. Please
pay attention to the above operation sequence.
【Power Supply Connection】
PoE power supply
The WAN port of this series device supports 48VDC PoE
power receiving, which conforms to IEEE802.3af/at standard.
12~48VDC power supply
This series device provides 1 DC power input
which is 3-pin 5.08mm pitch terminal block with
waterproof plug, the power supply supports
non-polarity. Power supply range: 12 ～ 48VDC. The pin
definitions of power supply are shown as follows:
Pin
1
2
Definition
【Mounting SIM Card】
This series of device supports 1 Micro SIM card slot or 1 Nano
SIM card slot, provides 2 SIM card slots for redundant backup.
Notice:
If the SIM card needs to be changed, the device should
be power off first in case of damaging the card.
【Setting Reboot/ Restore Factory Setting Button】
This series device provides 1 reset button, press the
button for 1-2S then release it to reboot the device;
press the button for 5S then release it to restore
factory defaults.
【Checking LED Indicator】
This series device provides LED indicators to monitor the
device working status with a comprehensive simplified
troubleshooting; the detailed status of each LED is described
in the table as below:
LED
Indicate
ON
RUN
Blinking
OFF
ON
Blinking
WLAN
OFF
Blinking
5G
OFF
ON
WAN
Blinking
OFF
3
V-
FG
V+
Description
The device is powered on or the
device is abnormal.
The device is running normally
The device is powered off or the
device is abnormal.
Wireless WiFi network is enabled
Wireless WiFi is in an active
network status
Wireless WiFi network is running
abnormally or turned off
5G module is operating normally
5G module isn't operating
WAN port has established valid
network connection
WAN port is in network active
status
WAN port hasn't established valid