- ページ 4

キッチン家電 Elite EPM-250のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Elite EPM-250 4 ページ。 Classic countertop popcorn maker
Elite EPM-250 にも：取扱説明書 (17 ページ)

ページを印刷する

POPPING INSTRUCTIONS

1. Make sure the popcorn mak

following:

2. Before using the unit, please check carefully to be sure voltage (AC12

~60Hz) is suit

able to your home.

3. Clean the internal surface of the kettle with warm soapy water, rinse well

and dry with clean cloth. Wipe do wn inner and outer surfaces of the main

popcorn unit with damp cloth.

Main popcorn unit has a 2-function switch as follows:

- LIGHT: to turn the internal light bulb on.

- POP: to turn the stirring stick motor & heater on.

nstall

popping kettle by hooking the kettle onto the hanga

popcorn unit (see step 1).

6. Insert the internal kettle plug into the socket on the ceiling inside the main

popcorn unit.

7. Plug the external power cord into an electric wall outlet.

Before pouring oil or ker

nels into the kettle, lift lid using t

(1 tablespoon of vegetable, corn, peanut, or coconut oil).

9. Turn both LIGHT & POP switches to ON position. The light, heater and

motor will be on. Let the kettle preheat the oil for about 2 to 3 minutes. Turn

the POP switch to off position and add 1/3 cup of corn kernels (Note: 1/3

measuring cup included) and close lid to the kettle. Turn POP switch back

on, stirrer will begin to rotate and heater will heat up the oil and corn.

CAUTION: Lid might be hot – it is recommended to use an oven mitt.

10.

Popcorn starts popping out through the lid after about 2 minutes.

11.

When unit is finished popping – you will no longer hear the corn popping –

immediately turn the POP switch to the OFF position and pull down the

handle bar of the kettle to release any remaining popcorn in the popper.

This will also stop the remaining popcorn from cooking any further and

avoid possible burning.

12.

Keep POP switch off if the unit is not in use. Always allow the kettle to

cool-down approximatel

y 5-10 minutes between continuous batches of

three. This will avoid over-heating the kettle

13.

Remove plug from power supply when the unit is not being used.

14.

Repeat step 8 to 10 for continuous popping.

er is u

npl

ugged before you do any of the

rs inside the main

he lid tab. Add oil

-5-

CLEANING AND MAINTENANCE

It is strongly recommended to clean the kettle frequently to avoid burning

excess oil onto the bottom of the inner pot.

After using the popcorn machine, let it cool, and use a wet cloth to clean the

main unit body. It is strongly recommended to wash and dry the tray after each

use to avoid any bacteria buildup. The light bulb is replaceable with an AC120V

10W bulb.

KETTLE QUICK CLEANING PROCEDURE

Turn the POP control to off. Pour 4 to 6 ounces of water (NO detergent is

necessary) into inner kettle pot. Switch to POP to boil the water and let the

stirrer turn in order to remove excess oil stuck on the surface. Leave on for

approximately 1-2 minutes. Shut off and let cool. After cooling, pour out the

water out and discard. CAUTION: THE KETTLE MAY BE HOT.

You may also remove the kettle and clean it with a Scotch-Brite scouring pad

(Not included). NEVER immerse kettle or electrical plug in water or other

liquids.

You may also consider using a cleaning product designed for removing carbon

deposits and is specially formulated to clean popcorn kettles.

-6-