- ページ 2

アクセサリー Anywire B284SB-02-1KNP30のPDF マニュアルをオンラインで閲覧またはダウンロードできます。Anywire B284SB-02-1KNP30 16 ページ。

ページを印刷する

[About Single Unit Simplified Replacement]

During replacement of a slave unit, this function enables automatic settings of

address and parameters of the existing slave unit into a new slave unit. (After

replacement of the slave unit, address and parameter setting procedure using the

address writer is not required.)

■Step 1 Turn OFF the 24V DC power supply for the master unit.

■Step 2 Disconnect a slave unit to be replaced.

ASLINK

master unit

■Step 3 Connect a new slave unit.

NEW

ASLINK

master unit

■Step 4 Turn ON the 24V DC power supply to the master unit.

！

CAUTION

- It is necessary that both the master unit and slave unit should be compatible

with the single unit simplified replacement function.

- Before disconnection and connection of the slave unit, be sure to turn OFF the

power supply.

- For compatibility of a slave unit with the single unit simplified replacement

function, see the lot No. and the manual for the slave unit.

- When a slave unit of a new function version is replaced with that of an old

function version, the single unit simplified replacement function cannot be

used.

- Operation is enabled in the case where the model of the slave unit before

replacement is the same as that after replacement.

- If the model of the slave unit before replacement is different from that after

replacement, a model mismatching error occurs, disabling address and

parameter settings.

- Operation is enabled in the case where the address of the slave unit for

replacement is the factory-set address (bit address 511).

- Several slave units cannot be simultaneously replaced. For replacement of

several slave units, conduct the replacement procedure for each unit one by

one.

- For a slave unit incompatible with the single unit simplified replacement

function, set an address and parameters by using the address writer as in the

conventional manner.

- For details of the single unit simplified replacement function (limitations,

conditions, etc.), refer to the manual for the master unit.

■Identification of function version

Function version information is given on the lot label.

* The design and contents of the lot label may vary depending on the product

model and lot No.

Function version:

When an equipment parameter

is changed due to functional

upgrading, etc., the function

version will be updated (for

example: A→B→C).

When a slave unit of a new

function version is replaced

with that of an old function

version, the single unit

simplified replacement function

cannot be used.

-B284SB0*1K**P30 2/16-

[Functions]

Model

ASLINKSENSOR 2-wire type (non-isolated)

Indication mode

Gage pressure

Pipe connection

M5 female thread

bore diameter

Bit transmission

Word transmission*

Single unit simplified replacement*

Remote address change*

Alarm bit

Threshold setting (upper limit, lower limit)

Functions

Operation mode setting (hysteresis mode, window comparator mode)

Input logic selection

Input response time setting

Alarm setting (upper limit, lower limit)

Alarm judgment time setting

Zero correction

Bit address setting

Address

Word address setting

*1 It depends on lot No. whether this function is available or not.

*2 This unit can be used in connection to the AnyWireASLINK system for word transmission.

Note that this unit cannot handle word data by setting a word address.

*3 To use these functions, a master unit compatible with each function is required.

For details, refer to this manual together with the manual for the master unit.

■Detecting functions (Status details)

Slave unit voltage drop

Sensing level drop

I/O cable disconnection

Functions

I/O short-circuit

I/O power supply drop

[Function Compatibility by Lot No.]

This unit has undergone addition of functions and change of specifications

according to version upgrading. Available functions and specifications of the unit

vary depending on lot No.

Function/specification

Remote address change

Single unit simplified replacement

Word transmission*

LED indication for single unit

simplified replacement function*

*4 This unit can be used in connection to the AnyWireASLINK system for word transmission.

Note that this unit cannot handle word data by setting a word address.

*5 In the case where a lot No. indicates year and month digits of "15I" or later, the single unit

simplified replacement function works even if the lot number does not support the LED

indication for the single unit simplified replacement function.

(When the master unit executes the single unit simplified replacement function,

addresses/parameters will be written, if specified conditions are satisfied.)

■How to check

Lot No. is indicated on the lot label.

Example:

Lot No. 19ECBNB

Year and month

○

Lot No.

Available with lot No. that indicates year and

month digits of "15I" or later.

Available with S/W version "B" or later version

(If lot No. is indicated in 3 digits (year and

month only), these functions are not available.)

Side surface of

this unit

S/W version

○