- ページ 2
セキュリティシステム Duevi EZY-LANのPDF マニュアルをオンラインで閲覧またはダウンロードできます。Duevi EZY-LAN 12 ページ。 Wireless alarm panel with ethernet + wi-fi + gsm + lte
Duevi EZY-LAN にも： ユーザーマニュアル (4 ページ), ユーザーマニュアル (5 ページ)
ページを印刷する3
LED signals
The system status indication of the RGB LEDs (6)
can be disabled in the programming.
The intensity of the RGB LEDs (6) is reduced after
60 seconds of inactivity of the control panel.
When the control panel is powered only by
battery, the LEDs (2) (3) (4) are switched off and
the multi-colored LED ring (6) only flashes
periodically.
Led
Status
off
slow flashing
1 Power
quick flashing
steady on
off
quick flashing
2 Ethernet
steady on
off
slow flashing
3 Wi-Fi
quick flashing
steady on
off
slow flashing
quick flashing
4 GSM / LTE
steady on
RGB multicolor led ring (6)
Green
Disarmed
Green / Blue
Disarmed with door open
(blinking)
Green / Red
Disarmed with alarm memory
(blinking)
Red
Totally armed
Partially armed
Orange
Exit time (flashing)
Entry time (flashing)
Violet
Alarm in progress
(blinking)
White
Panel in SETUP mode
(blinking)
Azure
Panel in TEST mode
(blinking)
Indication
Panel turned off
No power supply
+ battery ok
Power supply
present + battery
absent
Power supply
present + battery
ok
cable
disconnected
cable connected
+ internet / P2P
absent
cable connected
+ internet / P2P
present
Module turned off
Wi-Fi access
point mode
Wi-Fi router
mode + internet /
P2P absent
Wi-Fi router +
internet / P2P
mode present
Module turned off
SIM registered /
GSM mode
SIM not
registered or
other problems
SIM registered /
LTE mode +
internet / P2P
present
4
Power supply and battery
The control panel is powered by an external
12Vdc 2Ampere power supply to be connected to
the appropriate jack input (11).
Power must be supplied from a Limited Power
Source (LPS) ES1, PS2.
Internally there is a 3.7V 3Ah rechargeable lithium
battery, which guarantees an autonomy of up to
15 hours in the absence of external power.
When the battery level drops below the minimum
operating threshold, the panel switches off
automatically, to preserve the life of the battery
pack.
ATTENTION:
DANGER OF EXPLOSION IF THE
BATTERY IS REPLACED WITH ANOTHER
OF THE WRONG TYPE. DISPOSE OF
USED BATTERIES ACCORDING TO THE
INSTRUCTIONS
5
Using the SIM card
The control panel manages SIM card in nanoSIM
format. The LTE data connection must be set in
the software programming.
ATTENTION
THE SIM CARD MUST BE INSERTED AND
REMOVED FROM ITS HOUSING WITH THE
PANEL SWITCHED OFF. WITH THE PANEL
SWITCHED ON, BOTH THE SIM AND THE
DEVICE CAN BE DAMAGED, IN ADDITION
THE SIM IS DETECTED ONLY AT STARTUP.
6
Turning ON
When the control panel is off, to turn it on, simply
connect the external power supply or briefly press
the PWR button (8). The led ring flashes white and
the control unit starts up.
7
Turning OFF
When the control panel is on and disarmed, to
turn it off, carry out the following procedure:
1. Disconnect the external power supply
2. Long press the PWR button (8), the led ring
lights up orange, continue to hold it down until
a long beep is heard.
3. Release the PWR button (8)
4. The control panel is off