- ページ 4
セキュリティセンサー Duevi EZY-LANのPDF マニュアルをオンラインで閲覧またはダウンロードできます。Duevi EZY-LAN 12 ページ。 Wireless alarm panel with ethernet + wi-fi + gsm + lte
Duevi EZY-LAN にも： ユーザーマニュアル (4 ページ), ユーザーマニュアル (5 ページ)
ページを印刷する11 Homepage (SETUP)
By pressing the ENTER IN SETUP button, the
control unit switches to programming mode and
the RGB LEDs of the control panel flash white.
The homepage transforms from a simple view into
a configuration page.
Press the icon
(gear) relating to the parameters
to be modified.
PLEASE NOTE:
1) After each change, press the icon
(green check) at the top right to
confirm
2) Pressing the icon
top left of each page takes you back to
the previous screen. If any changes
have been made, you are asked to
confirm or cancel the changes.
3) The changes made in the software will
be active in the control panel only after
executing the "SEND TO PANEL"
command
11.1 System
Date and time settings
•
NTP server
•
Time zone
•
Daylight savings time
System Settings:
•
Login with password
•
Reset to factory default
•
Reboot of the panel
11.2 Connections
PRIORITY OF CONNECTIONS
Ethernet is the primary channel that is used
if a network cable is connected.
Wi-Fi (if set in router mode) is the alternate
channel used when a network cable is not
connected.
LTE (if enabled) is the channel used when
there is no Ethernet or Wi-Fi connection or
there is no internet on one of the two
connections.
Ethernet settings
•
IP assignment: Static / DHCP
•
[If static IP] IP address, Subnet mask,
Gateway
Wi-Fi settings
Mode = <disabled>
The control panel Wi-Fi is turned off.
(left arrow) at the
Mode = <Router>
In this mode the control unit uses its own Wi-Fi
to connect to a Router/AP.
•
Router SSID: name of the Wi-Fi router to
which the control unit connects
•
Router Password: password of the Wi-Fi to
which the control unit connects in Router
mode
•
Security: WEP, WPA2 / WPA1 / PSK, WPA2 /
PSK
•
IP assignment: Static / DHCP
•
[If static IP] IP address, Subnet mask,
Gateway
Mode = <Access Point> (AP)
In this mode it is possible to connect directly to
the Wi-Fi of the control panel with a device
(phone, tablet or PC). The control panel acts as
a DHCP server and assigns an IP of the
192.168.5.x series.
•
AP SSID: Wi-Fi name of the control panel in
AP mode
•
AP Password: Wi-Fi password of the control
panel in AP mode
•
Security: WEP, WPA2 / WPA1 / PSK, WPA2 /
PSK
GSM + LTE settings
•
Module enable: on / off
•
SIM Pin
•
Max SMS per day (0 = no limit)
•
Use SIM data: on / off
•
APN
Voice message recording
Within the GSM section, press the icon
to access the page where you can manage the
voice message (maximum duration 60 seconds)
that the control panel uses for alarm calls.
This procedure can only be used if:
✓ a valid SIM with sufficient credit for the
call is inserted
✓ the GSM module is correctly connected
to the operator
✓ the GSM module is not connected in
LTE
Proceed as follows:
•
Enter the telephone number to be called by
the control panel and press "CALL THE
NUMBER"
•
The control panel makes a call to the
telephone number entered. Answer the call
•
Press the desired command between
START, STOP or LISTEN
•
Press HANG UP THE CALL
(gear)