- ページ 3
ハンドヘルド cascade corporation Palm 6030844のPDF セットアップ方法をオンラインで閲覧またはダウンロードできます。cascade corporation Palm 6030844 4 ページ。 Setup kit for force control products
ページを印刷するCapturing Force Control
Diagnostics Page
Follow the steps below to capture the Force Control Diag-
nostics Page as a 'memo' in the Palm computer. This
enables viewing the page or downloading (Palm 'HotSync')
to your PC.
1
Cycle the Clamp through a CLAMP/HOIST cycle,
leave truck running. (current settings will be stored in
Diagnostics Menu in controller).
2
Connect the Palm to the system controller pigtail using
the Cascade adapter cable.
3
Turn the Palm On and tap the 'Home' icon to see the
Cascade page with ptelnet communications applica-
tion ('computer screen' icon).
4
Tap ptelnet, and tap On button on menu bar that
appears across bottom of screen ('On' button highlights,
blinking cursor appears):
On
tl Esc Kbd VT
5
Tap the 'scroll down' icon located at the lower LH side
of the Palm character screen to bring up the 'Options/
Edit' menu shown opposite above.
6
Tap 'log' and check 'Active' and 'Log Header' (oppo-
site), tap OK.
7
Cycle the truck key ON/OFF, then ON. Palm screen
may show words 'arm movement'.
8
Press the Enter key ('Note Pad squiggly line' key on RH
side of Palm) and look for the words 'arm movement'
9
Press the Enter key again which brings up the Force
Control main menu. Select units, then select menu 3 -
Diagnostics Page (bottom right).
10
Tap the 'scroll down' icon to bring up the 'Options/
Edit' menu again (top right).
11
Tap 'log' again, uncheck 'Active' and 'Log header',
check 'Hex dump' (opposite). Tap OK. Turn ptelnet
OFF by unhighlighting 'On' at bottom of screen:
On
tl Esc Kbd VT
12
Tap the 'Home' icon, locate and tap the 'Memo Pad'
icon, which brings up the captured Diagnostics Page
(opposite) as the first new 'memo'.
You can now view the Diagnostics Page on the Palm by
scrolling, or you can download ('HotSync') the page to
your PC. NOTE: PC must have Palm application
software to download the memo.
¥
Macros
AC0730.ill
¥
Macros
AC0870.ill
5
Options
menu
ptions
Network
Serial
Terminal
Macros
Log
About
3
Home (All
Applications)
n
Ctl Esc Kbd VT
Icon
Scroll
Down
Icon
5
AC0773.ill
og options
□
Active
□
og header
□
Hex dump
K
Cancel
On
Ctl Esc Kbd VT
Macros
AC0869.ill
9,12
❏ Switch 1
❏ Switch 2
■ Load Weight
❏ Calculated Clamp Force
■ Measured Clamp Pressure
■ Calculated Clamp Pressure
■ Clamp Force/Weight Ratio
❏ Pulsewidth
❏ Hoist Pressure
❏ Calibrated Load Pressure
❏ Calibrated Attachment Pressure
❏ Trimpot
❏ Measured Pressures
❏ EEprom values
❏ EEprom values
❏ EEprom values
❏ EEprom values
On-Off
Edit
N
S
T
M
L
A
Macros
Enter
('Note Pad' Key)
og options
□
Active
□
og header
□
Hex dump
OK
ancel
On
Ctl Esc Kbd VT
Macros
AC0874.ill
Closed
Open
2000 lbs.
4000 lbs.
1400 psi
1400 psi
14
2800
800 psi
800 psi
800 psi
50
1,1,2,1
1,1,1,1,7,208,14,12,10
10,240,175,3,132,3,32
0,245,1,2,14,144,1,252
12,128,3,232,10,240,4,176