ストレージ DANE-ELEC SO EXTREMEのPDF スタートマニュアルをオンラインで閲覧またはダウンロードできます。DANE-ELEC SO EXTREME 2 ページ。 Ssd migration kit
DANE-ELEC SO EXTREME にも：データシート (2 ページ)

ページを印刷する

PACKAGING

CONTENTS

intel® X25-m saTa solid-state drive

2.5" dane-elec enclosure

with frame and screws

usb cable 1.1/2.0

64mb usb drive

Quick start Guide

with acronis®

migrate easy 7.0

and superduper!

for mac, v2.5

MIGRATION

GETTING

STARTED

STEPS

ToTal daTa and sofTware on lapTop musT be

The saTa laptop ssd migration kit includes not only

the saTa solid-state drive to replace your slow exist-

less Than capaciTy of new ssd.

ing saTa spinning hard drive; the kit also includes a

complete external usb drive case to make the migration

before you start, refer to your computer's documentation

to determine whether your system supports serial aTa

possible and then to repurpose the old drive as an

external drive after the migration. The migration software

(saTa) on the motherboard and the location of the saTa

connectors.

is included on a usb flash drive that can also be reused

for other purposes after the migration.

This kit assumes that your current laptop drive is a saTa

Important: Do not remove your old hard drive

drive. This kit and ssd drive will noT work as a replace-

until the cloning process is complete.

ment for a paTa drive.*

before you begin, obtain the steps from your laptop

manufacturer on removing the old hard drive and gather

the tools necessary. final assembly of the migration kit

itself requires a small phillips-head screwdriver.

HANDLING

PRECAUTIONS

disk drives are fragile and very sensitive to static

If your PC does not have SATA connectors, you will

electricity. To protect you and your system, take the

need to purchase a SATA host adapter that is com-

following precautions:

patible with your computer and operating system.

Then, using the host adapter manufacturer's installa-

• Turn off the power of the host system prior to

tion instructions, you will need to install the adapter

attempting installation, but leave the power plug

with the corresponding driver. You will also need the

connected.

following items:

• Keep the drive in the protective anti-static

container until you are ready to install the ssd.

• Four 6-32 UNC mounting screws and a screw-

• Wear a wrist strap and connect the ground strap to

driver. (2.5" Form factor only)

the computer case to minimize static electricity.

• A SATA interface cable with a maximum length

• Handle the drive with care. Do not touch the

of 1 meter. (Desktop usage model only)

connectors.

• A SATA-compatible (2.5" Form factor) or micro-

• Do not remove the encasement or disassemble the

SATA (1.8" Form factor) power cable or adapter.

drive, as such actions void the warranty.

(Desktop usage model only)

FOR MICROSOFT WINDOWS

A. Prepare the new SSD drive for migration.

C. Replace the old hard drive with the new SSD drive.

This assembly is temporary for the cloning process and

1. follow the instructions from your laptop manufacturer to

does not require the screws that will be used to secure

remove the old hard drive.

the final assembly if the old drive will be reused as an

2. remove the new ssd from the temporary external ssd

external drive.

usb drive assembly.

3. set both drives on a flat surface close to each other and

1. open the included usb case by sliding the case face-

compare the height or thickness. if the new ssd drive is

plate and circuit board out of the case.

substantially thinner, use the included frame and longer

2. align the new saTa ssd drive with the saTa connec-

screws to make the new ssd closer to the same thickness.

tor on the circuit board and gently complete the saTa

4. install the new ssd in the laptop and reassemble the

connection.

laptop according to the instructions from your laptop

3. slide the circuit board and ssd assembly back into

manufacturer.

the case. This will protect the electronics of the circuit

5. start your laptop as normal. your system bios may note a

board from accidental contact during the cloning. There

configuration change that requires your confirmation.

is no need to screw the case together at this point.

D. Repurpose your old internal hard drive

B. Clone the old drive to the new SSD.

1. pull out the circuit board with plug from the enclosure.

1. after windows is running as normal, attach the includ-

2. slip your old internal hard drive onto the plug

ed usb flash drive and run the acronis migrate easy

3. secure your old hard drive by inserting one of the screws

installation from that drive. The installation program may

in each of the side and bottom mounting holes.

require the system to be rebooted and reQuires in-

4. insert the hard disk onto enclosure.

ternet access for activation. The serial number required

5. secure enclosure by locking screws.

for software activation is printed on the warranty and

2. after the installation, remove the usb flash drive, and

attach the temporary external ssd usb drive created in

ssd preparation steps.

3. run the acronis migrate easy software from the win-

dows start menu.

4. The migration software will walk you through the "disk

cloning" process. read each step carefully.

5. when ready, the migrate easy will instruct you to

reboot the system to begin the actual cloning of the old

drive to the new drive.

6. upon completion, you will be instructed to shut down

the system.

FOR APPLE MAC OS X

A. Prepare the new SSD drive for migration.

6. click "options".

This assembly is temporary for the cloning process and

7. choose the partition scheme (Guid for intel-based

does not require the screws that will be used to secure

macs, apple partition map for power pc macs) and

the final assembly if the old drive will be reused as an

accept the page.

external drive.

8. click "partition".

1. open the included usb case by sliding the case face-

C. Clone the old drive to the new SSD.

plate and circuit board out of the case.

1. run superduper! from the included usb flash drive.

2. align the new saTa ssd drive with the saTa connec-

The serial number required for software activation is

tor on the circuit board and gentry complete the saTa

printed on the warranty and copyright page of the

connection.

Quickstart Guide.

3. slide the circuit board and ssd assembly back into

2. choose to copy the old drive to the new ssd drive.

the case. This will protect the electronics of the circuit

read each step carefully.

board from accidental contact during the cloning. There

3. click "copy now".

is no need to screw the case together at this point.

4. upon completion, shut down the system.

B. Partition the new SSD.

D. Replace the old hard drive with the new SSD

for maximum reliability:

drive.

a. partition the new drive on your mac before cloning.

1. follow the instructions from apple to remove the old

b. do not run any other application during any part of

hard drive.

the migration process.

2. remove the new ssd from the temporary external

c. disable any antivirus software during the migration

ssd usb drive assembly.

process.

3. set both drives on a flat surface close to each other

d. remove all other usb devices.

and compare the height or thickness. if the new ssd

e. Do not use the Keyboard USB port for the USB Flash

drive is substantially thinner, use the included frame and

or ssd drive.

longer screws to make the new ssd closer to the same

1. attach the temporary ssd usb drive created in the

thickness.

ssd preparation steps.

4. install the new ssd in the laptop and reassemble the

2. start the "disk utility" found in applications/utilities.

laptop according to the instructions from apple.

3. select the new external ssd drive hardware in the disk

5. start your laptop as normal.

utility's sidebar.

4. click on the "partition" tab.

D. Repurpose your old internal hard drive

5. use disk utility to divide the new drive as needed,

1. pull out the circuit board with plug from the enclosure.

which will most likely be as a single large partition. use

2. slip your old internal hard drive onto the plug

"mac os extended (Journaled)" as the format type and

3. secure your old hard drive by inserting one of the

name the new drive the exact same name as the drive

screws in each of the side and bottom mounting holes.

being replaced.

4. insert the hard disk onto enclosure.

5. secure enclosure by locking screws.