- ページ 2
室内装飾品 casiii STAND-35のPDF インストレーション・マニュアルをオンラインで閲覧またはダウンロードできます。casiii STAND-35 2 ページ。
ページを印刷する
STEP 5
Install the Control Panel
6
STEP 6
Install the Cable
Management Tray
B
x4
Method 1
F
4x4
3
4
B
Firstly, rotate the screws (B) incompletely into the supporting beam (4)
with Allen Key (F), which means do not tighten them. Next, slide one
side of the cable management tray (3) into the screws (B), then the
other side Finally, tighten the screws (B) with Allen Key (F).
B
x4
Method 2
D
x4
Install the cable management tray as Method 1, Step 6.
F
3
4x4
Power port
Port for
hand switch
Slide one side
3
1
Buckle the other side
2
B
D
4
When the supporting beam stretches over 1720 mm,
the cable management tray needs to be mounted on
D
the middle of the supporting beam.
B
Do not stretch the support
beam beyond this hole
7
Port for cable
connected to the
lifting column
Button introduction: There are seven buttons
"▲" , "▼" , "1" , "2" , "
"
(1) "▲" : Adjust the desk upwards
(2) "▼" : Adjust the desk downwards
(3) "1" : Position 1, first height position saved by the user
(4) "2" : Position 2, second height position saved by the user
(5) " " : the display shows "3", which means the position of the
standing height the user saved.
(6) " " : the display shows "4", which means the position of the
sitting height the user saved.
(7) "M" : Height saving button, for height memory function;
Tighten
Child lock: for security
Common fault treatment
The following tips will help you detected and eliminate the common fault
and error.If the fault you met is not listed below, please contact with your
supplier. Only themanufacturer and professionals are capable for investigating
and correcting those fault and error.
Fault phenomenon
No response while long pressing
down arrow after connected with
a power supply
No response while pressing up
arrow/ down arrow after
connected with a power supply
Rising in a low speed
The motor not move as instructed
Go down but not go up
Downward sliding
Frequently Reposition
Overwork
（Duty cycle: Max 2min on/18min OFF）
Not enough up&down height
Waste disposal
Child lock function:
●
a. When the child lock is turned on, the child lock blue indicator light (﹀ and M directly
above) lights up
b. Press the button indicator to flash once
c. To unlock or start the child lock, you need to press and hold the M button for about 5
seconds.
d. Only when the child lock is unlocked, all the buttons can work normally.
Height Adjustable Function:
●
Press the"▲" or "▼" button to adjust the height. The LED display shows the current height.
Height Memory Function:
●
a. Press UP or DOWN button and adjust the height to the desired height. Press "M" to
save the height, and the screen will display "
Press "1" , "2" ,or "
1 or 2 3, or 4, which will show in the display screen as "
b. Press "1", "2" and "
you saved.
● USB charging function：
a. USB output: QC2.0/QC3.0, 5.0v / 9.0v / 12.0v, ±5%, current: 1.0a
● Collision prevention sensitivity adjustment - optional features:
a. Press and hold the "▲" "▼" button for 5 seconds at the same time to switch the
sensitivity. There are four levels of sensitivity (A-3, A-2, A-1, A-0). Each operation will
"
"
"M"
switch the sensitivity into the next level.
b. The display shows "
low sensitivity; Display shows "
sensitivity (factory default is A-3);
c. During height adjustment, when tabletop comes in contact with another object, it
instantly stops and reverses to avoid damage.
d. Press and hold the "▲" "▼" button for 5 seconds at the same time. If the display
does not display the above code, there is no anti-collision function.
● Troubleshooting:
a. Reset: When the LED shows"
height and rebounds to stop, it means the reset has been finished.
b. When it does't work and the LED shows "E01" or "E02", please retry 18 mins later.
c. If the "▼" button does't work, please check the cable connection and then cut off the
power for at least 10 seconds. Reconnect to the power and press "▼" button to start the
reset process when it shows the "
d. If all these above process are inefficient, plz contact our customer service.
Attention
1. Power supply: AC100V-240V,50/60Hz
2. Service Environment: 0-40℃
3. Unplug the power plug before cleaning, wipe the dust on surface with slight wet
dishcloth when cleaning, be careful not to let the drops into the internal parts, not loose
Method
the connector.
4. The electric box contains electronic components, metals, plastics, wires etc., so
1.Check if all the cables be connected well
dispose of it in accordance with each country's environmental legislation, not the
2.Contact your supplier or dealer
general household waste.
5. Check carefully to ensure correct and complete assembly before using.
1.Check if all the cables be connected well
6. Be familiar with all functions and program settings of the product before first use.
2.Contact your supplier or dealer
7. Children are forbidden to play on the product because of unforeseen action when
playing, so any dangerous consequences caused by this improper action will not be on
1
Check if overloaded, max loading: 125kg;
.
manufacturers.
2
Contact your supplier or dealer
.
8. Slight noise caused by the V-ribbed belt or brake system due to structure will not
have any effect on the use of the equipment.
1. Contact your supplier or dealer
9. Corrosive or abrasive materials are forbidden to clean the equipment. Must ensure
1.Reposition
that the cleaner used will not pollute the environment.
10. This appliance can be used by children aged from 8 years and above and persons
2.Contact your supplier or dealer
with reduced physical, sensory or mental capabilities or lack of experience and
1
Check if overloaded, max loading: 125kg;
knowledge if they have been given supervision or instruction concerning use of the
.
appliance in a safe way and understand the hazards involved. Children shall not play
2
Contact your supplier or dealer
.
with the appliance.
1
Check if overloaded, max loading: 125kg;
.
11. Cleaning and user maintenance shall not be made by children without supervision.
12. If the supply cord is damaged, it must be replaced by the manufacturer, its service
2
Contact your supplier or dealer
.
agent or a similarly qualified person in order to avoid a hazard.
1
Restart after suspend for 18mins while
.
connecting with power;
13. Please make sure there is no hazard sources in your operating environment. e.g.,
do not litter the tools around. Always be careful to treat the packaging materials in order
2
Contact your supplier or dealer;
.
to avoid any possible danger, e.g. plastic bag may lead to choking hazard to children.
1. Press "M"and "3" together for 3 seconds or
14. Keep the original package of the equipment if necessary in case of the future use in
more, after hearing continuous beeping for twice,
transportation.
it will restore factory settings
2.Contact your supplier or dealer
This marking indicates that this product should not be
disposed with other household wastes. To prevent
possible harm to the environment or human health
from uncontrolled waste disposal, recycle it responsibly
to promote the sustainable reuse of material resources.
To return your used device, please use the return and
collection systems or contact the retailer where the
product was purchased. They can take this product for
environmental safe recycling.
";
" , "
" then, that is, save the height to the corresponding position
" ,"
", or "
", or "
";
" , "
"button directly to automatically adjust the memory height
" , the anti-collision function is off; the display shows "
",
", medium sensitivity; display shows"
", high
" , press "▼" button until the desk reaches its lowest
".
www.casiii.com
Design in USA