見る Casio 2291のPDF 知り合いになるをオンラインで閲覧またはダウンロードできます。Casio 2291 2 ページ。

Casio 2291 知り合いになる
Module No. 2291
Congratulations upon your selection of this CASIO watch. To get the most out of your purchase, be sure to carefully read this manual and keep it on hand for later reference when necessary.
Button operations are indicated using the letters shown in the illustration.
Each section of this manual provides you with the information you need to perform operations in each mode. Further details and technical information can be
found in the "REFERENCE" section.
(Light)
Press C to change from mode to mode.
In any mode, press L to illuminate the display.
Pressing C in the Timekeeping Mode displays either the Countdown Timer or Stopwatch screen. The screen that appears first is the one that was last on the display when you exited the
Countdown Timer/Stopwatch Mode.
Timekeeping Mode
Use the Timekeeping Mode to set and view the current
Month – Day
time and date.
Day of week
To reset the second's count to zero
1. In the Timekeeping Mode, hold down A until the
2. Press D to reset the second's count to 00.
PM indicator
Seconds
3. Press A to exit the setting screen.
Hour : Minutes
To set the time and date
1. In the Timekeeping Mode, hold down A until the
2. Press C to move the flashing in the sequence shown
Seconds
Day
See "Daylight Saving Time (DST)" for details on the DST setting.
3. While a setting is flashing, press D to increase it.
4. Press A to exit the setting screen.
Note
The day of the week is automatically displayed in accordance with the date (year,
month, and day) settings.
The year can be set in the range of 2000 to 2039.
The Watch's built-in full automatic calendar automatically makes allowances for
different month lengths and leap years. Once you set the date, there should be no
reason to change it except after you have the Watch's battery replaced.
To toggle between the 12-hour/24-hour timekeeping formats
In the Timekeeping Mode, hold down B for about two seconds to toggle between 12-
hour and 24-hour timekeeping.
With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for
times in the range of noon to 11:59 p.m. and no indicator appears to the left of the
hour digits for times in the range of midnight to 11:59 a.m.
With the 24-hour format, times are displayed in the range of 0:00 to 23:59, with 24
indicator.
The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is also
applied in all modes.
Daylight Saving Time (DST)
Daylight Saving Time automatically advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To toggle the Timekeeping Mode time between DST and Standard Time
1. In the Timekeeping Mode, hold down A until the
2. Press C to move the flashing to the DST On/Off
3. Press D to toggle between Daylight Saving Time (ON)
4. Press A to exit the setting screen.
The DST indicator appears on the display to indicate
that daylight saving time is turned on.
Press
.
TIMEKEEPING
second's digits start to flash, which indicates the setting
screen.
Pressing D while the second's count is in the range
of 30 to 59 resets the seconds to 00 and adds 1 to
the minutes. In the range of 00 to 29, the minute's
count is unchanged.
second's digits start to flash, which indicates the setting
screen.
below to select other settings.
DST
Hour
Minutes
Month
Year
second's digits start to flash, which indicates the setting
screen.
setting.
and standard time (OFF).
GETTING ACQUAINTED
GENERAL GUIDE
Countdown Timer/Stopwatch Mode
Countdown Timer
Hold
down
The start time of the countdown timer can be set within a range of 1 minute to 24
hours. The operation of the countdown timer is configured to make it useful for timing
yacht races.
All of the operations in this section are performed in the Countdown Timer Mode.
Use the procedure below to switch between the Countdown Timer and Stopwatch.
To switch between the Countdown Timer and Stopwatch
1. Enter the Countdown Timer/Stopwatch Mode.
2. Hold down D for about two seconds to toggle the Countdown Timer Mode and
Stopwatch Mode.
Countdown Timer Mode
Hours
Note that the above steps work only when the currently displayed screen is
initialized (reset). The Countdown Timer is initialized when its start time is displayed,
while the Stopwatch is initialized when it shows all zeros.
See "STOPWATCH" for information about using the Stopwatch.
Countdown Timer Operation
The countdown timer counts down the displayed time in one-second increments,
starting from a countdown start time set by you. A progress beeper beeps each
minute, and each second for the last 10 seconds of the countdown. The operation of
the beeper is very useful for match race and ocean race timing.
Before using the Countdown Timer, you should set the countdown start time and
select either match race timing or ocean race timing as the timing method.
Match Race Timing
When you set up the countdown timer for match race timing, the countdown
automatically restarts from the countdown start whenever zero is reached. This type
of timing is best for match races, with start at regular intervals (every five minutes, for
example).
Ocean Race Timing
With ocean race timing, the stopwatch starts timing automatically as soon as the
countdown reaches zero. This type of timing is best for ocean racing, which is
conducted based on accumulated time following the start.
To set the countdown time
To select the timing method
To use the countdown timer
Press B while in the Countdown Timer Mode to start the countdown timer.
Press B while a countdown operation is in progress to pause it. Press B again to
resume the countdown.
To completely stop a countdown operation, first pause it (by pressing B), and then
press D. This returns the countdown time to its starting value.
Note
Match race timing continues until you stop it. Note that the progress beeper can
down the battery power after long periods, so you should stop the timing operation
when you are not using the countdown timer.
In the case of ocean race timing, stopwatch operation that starts at the end of the
countdown is the same as that for normal Stopwatch Mode timing. See "To measure
times with the stopwatch" for more information. Note that initializing the stopwatch
(clearing it to all zeros) after an ocean race timing operation also initializes the
countdown timer by returning it to its starting value.
Alarm Mode
Stopwatch
.
COUNTDOWN TIMER
Hold down
.
Minutes
Seconds
1. In the Countdown Timer Mode, hold down A until the
hour digit of the countdown time starts to flash, which
indicates the setting screen.
2. Press C to move the flashing between the hours and
minutes.
3. While a setting is flashing, press D to increase it.
To set the countdown start time to 24 hours, set
0:00.
4. Press A to exit the setting screen.
1. In the Countdown Timer Mode, hold down A until the
hour digit of the countdown time starts to flash, which
indicates the setting screen.
2. Press B to toggle the timing method between match
race timing (
indicator) and ocean race timing
(
indicator).
3. Press A to exit the setting screen.
2291-1
Stopwatch Mode