- ページ 7
コントロールユニット Danfoss AK-LM 330のPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。Danfoss AK-LM 330 8 ページ。 Adap-kool refrigeration control systems
ページを印刷するDisplay control
Measurements
AK error
Settings
Main switch
Display control A
Display control B
Display control C
Display control D
Sensor type and calibration
Measurements
AK error
Settings
Main switch
Saux 1 offset
2,3,4,5,6,7,8
Paux 1 offset
Paux 2 offset
Saux 1 sensor type
2,3,4,5,6,7,8
Paux 1 sensor type
AK-LM 330 Vers. 1.4x
When "ON", the controller is in alarm condition.
Main switch:
Set what should be read in "Display A"
Set what should be read in "Display B"
Set what should be read in "Display C"
Set what should be read in "Display D"
No reading = 0
"Thermostat 1" to be defined with setting = 1
"Thermostat 2" to be defined with setting = 2
"Thermostat 3" to be defined with setting = 3
"Thermostat 4" to be defined with setting = 4
"Thermostat 5" to be defined with setting = 5
"Thermostat 6" to be defined with setting = 6
"Thermostat 7" to be defined with setting = 7
"Thermostat 8" to be defined with setting = 8
"Thermostat 9" to be defined with setting = 9
"Thermostat 10" to be defined with setting = 10
"Pressostat 1" to be defined with setting = 11
"Pressostat 2" to be defined with setting = 12
"Pressostat 3" to be defined with setting = 13
"Pressostat 4" to be defined with setting = 14
"Pressostat 5" to be defined with setting = 15
"DI1 Alarm" to be defined with setting = 16
"DI2 Alarm" to be defined with setting = 17
"DI3 Alarm" to be defined with setting = 18
"DI4 Alarm" to be defined with setting = 19
"DI5 Alarm" to be defined with setting = 20
"DI6 Alarm" to be defined with setting = 21
"DI7 Alarm" to be defined with setting = 22
"DI8 Alarm" to be defined with setting = 23
"DI9 Alarm" to be defined with setting = 24
"DI10 Alarm" to be defined with setting = 25
"DI11 Alarm" to be defined with setting = 26
"DI12 Alarm" to be defined with setting = 27
"DI13 Alarm" to be defined with setting = 28
"DI14 Alarm" to be defined with setting = 29
"DI15 Alarm" to be defined with setting = 30
"DI16 Alarm" to be defined with setting = 31
When "ON", the controller is in alarm condition.
Main switch:
Correction of the signal from the sensor "Saux 1" if necessary
Do for Saux 2,3,4,5,6,7,8
Correction of the signal from the pressure transmitter "Paux 1" if necessary
Correction of the signal from the pressure transmitter "Paux 2" if necessary
Definition of the sensor type for the input "Saux 1"
Pt 1000 ohm defined with setting = 0
PTC 1000 ohm defined with setting = 2
Do for Saux 2,3,4,5,6,7,8
Definition of pressure transmitter type and pressure area for "Paux 1"
AKS 32 -6 defined with setting = 1
AKS 32 -9 defined with setting = 4
AKS 32 -12 defined with setting = 7
Menu operation RC8CC202 © Danfoss 09/2012
ON:
Regulation
OFF: Controller stopped
ON:
Regulation
OFF: Controller stopped
7