- ページ 4

コントロールユニット Danfoss CHV-X 15-125のPDF インストレーション・マニュアルをオンラインで閲覧またはダウンロードできます。Danfoss CHV-X 15-125 12 ページ。 Check & stop valve / check valves
Danfoss CHV-X 15-125 にも：インストレーション・マニュアル (8 ページ)

ページを印刷する

ENGLISH

Installation

Refrigerants

Applicable to HCFC, HFC, R717 (Ammonia),

R744 (CO

), Propane, Butane, Iso-Butane and

Ethane.

The valve is only recommended for use in

closed circuits. For further information please

contact Danfoss.

Temperature range

–60/+150°C (–76/+302°F)

Pressure range

52 bar (754 psi)

The valve must be installed with the spindle

on top vertically upwards or in horizontal

position (fig. 1). SCA-X valves should be

opened by hand without the use of tools

or other devices. The valve is designed to

withstand a high internal pressure. However,

the piping system should be designed

to avoid liquid traps and reduce the risk

of hydraulic pressure caused by thermal

expansion. It must be ensured that the valve

is protected from pressure transients like

"liquid hammer" in the system.

Flow direction

Direct the flow towards the cone as indicated

by an arrow on the valve housing (fig. 1).

Welding

The bonnet should be removed before

welding (fig. 2) to prevent damage to the

O-rings in the packing gland and the gasket

between the valve body and bonnet, as

well as the teflon gasket in the valve seat.

Be careful not to damage the teflon cone

ring and make sure the complete bonnet is

protected from dirt and water while removed.

Only materials and welding methods,

compatible with the valve housing material,

must be applied to the valve housing. The

valve housing must be free from stresses

(external loads) after installation.

The valve should be cleaned internally to

remove welding debris on completion of

welding and before the valve is reassembled.

Avoid welding debris and dirt in the threads

of the housing and the bonnet.

Do NOT remove or service the dark colored

grease between the spindle thread and

the bonnet. In case the grease has been

contaminated with dirt, debris, particles

or water the complete top part must be

replaced.

Stop check valves must not be mounted in

systems where the outlet side of the valve

is open to atmosphere. The outlet side of

the valve must always be connected to the

system or properly capped off, for example

with a welded-on end plate.

Assembly

Remove welding debris and any dirt from

pipes and valve body before assembly. Check

that the cone has been fully screwed back

towards the bonnet before it is repositioned

in the valve body (SCA DN 50-125) (fig. 3).

Important for the SCA-X valves:

Full capacity is only obtained when the

spindle is screwed outward, "into bonnet", i.e.

counterclockwise (fig. 3).

Tightening

Tighten the bonnet with a torque wrench, to

the values indicated in the table (fig. 3).

Please note that the table (fig. 3) containing

maximum torque must be adhered to and

never exceeded.

Important for SCA-X/CHV-X 50 - 125 valves:

For optimal flow the insert must be installed

as indicated in (fig. 10). Otherwise kv value

will be below indicated in the

technical brochure.

Colours and identification

The SCA-X and CHV-X valves are painted

with a red primer in the factory. Precise

identification of the valve is made via the

green coloured ID ring at the top of the

bonnet, as well as by the stamping on the

valve body. The external surface of the valve

housing must be protected against corrosion

with a suitable protective coating after

installation and assembly.

Protection of the name plate when repainting

the valve is recommended.

Maintenance

Packing gland (only SCA-X types)

When performing service and maintenance,

replace the complete packing gland only,

which is available as a spare part. As a

general rule, the packing gland must not be

removed if there is internal pressure in the

valve. However, if the following precautionary

measures are taken, the packing gland can be

removed with the valve still under pressure:

Backseating (fig. 4)

To backseat the valve, turn the spindle

counterclockwise until the valve is fully open.

Pressure equalization (fig. 5)

In some cases, pressure forms behind the

packing gland. Hence, a handwheel or a large

washer (pos. A) should be fastened on top of

the spindle while the pressure is equalized.

The pressure can be equalized by slowly

screwing out the gland.

Removal of packing gland (fig. 6)

Packing gland can now be removed.

Dismantling the valve (fig. 8)

Do not remove the bonnet while the valve is

still under pressure.

DN 15-40 (fig. 8a):

- Check that the gasket (pos. A+B) has not

been damaged.

- If the gasket (pos. A) has been exposed

to air or other refrigerants than listed in

this installation guide for more than

6 months it must be replaced.

- Check that the spindle is free of scratches

and impact marks.

- If the teflon cone ring has been damaged,

the whole cone assembly must be

replaced.

DN 50-125 (fig. 8b):

- Check that the spring (pos. A) is intact.

- Check that the gasket (pos. B+E) has not

been damaged.

- If the gasket (pos. A) has been exposed

to air or other refrigerants than listed in

this installation guide for more than

6 months it must be replaced.

- Check that the spindle (pos. C) is free of

scratches and impact marks.

- If the teflon cone ring (pos. D) has been

damaged, the whole cone assembly must

be replaced.

Replacement of the cone (fig. 9)

DN 15-40:

O-ring (pos. C) prevents the cone from falling

out. Pull the cone clear of the bonnet. Ensure

that the spring is not lost in the process.

Remove dirt, if any. Mount O-ring (pos. C) on

cone. Mount spring and cone in bonnet.

Do NOT remove or service the dark colored

grease between the spindle thread and

the bonnet. In case the grease has been

contaminated with dirt, debris, particles

or water the complete top part must be

replaced.

Assembly

Remove dirt, if any, from pipes and housing

before assembly. Important for the SCA-X

valves: Full capacity is only obtained when

the spindle is screwed outward, "into the

bonnet", i.e. counterclockwise (fig. 3).

Note:

For SCA-X and CHV-X sizes DN 15-40 it

is important to ensure that the lower

and upper part of the insert is tightly

screwed together (fig. 11) and that this

screw connection is kept tight during

repositioning of the cone in the housing.

Use a torque wrench to tighten the bonnet

(fig. 3).

Tightening

Tighten the bonnet with a torque wrench,

to the values indicated in the table (fig. 3).

Tighten the packing gland with a torque

wrench, to the values indicated in the table

(fig. 7).

Use only original Danfoss parts, (including

packing glands and gaskets) for replacement.

Materials of new parts are certified for the

relevant refrigerant.

In cases of doubt, please contact your local

Danfoss sales office.

DKRCI.PI.FL1.T2.ML | 520H6172 | 4