- ページ 3

ステレオ・イコライザー Free The Tone PA-1QBのPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Free The Tone PA-1QB 6 ページ。 Programmable analog 10 band eq graphic equalizer
Free The Tone PA-1QB にも：オーナーズマニュアル (6 ページ), マニュアル (16 ページ), オーナーズマニュアル (9 ページ), クイック・スタート・マニュアル (2 ページ)

ページを印刷する

Controls and Indicators

Rear Panel

INPUT LEVEL select switch

This switch is used to select PA-1Q series input

level according to the output level of the device

connected to the INPUT terminal. If you are connec-

ting an instrument level device, set the switch to the

INPUT terminal side. Or to connect a line level device,

set it to the OUTPUT terminal side.

INPUT terminal

Used to connect

a guitar/

bass, another

OUTPUT terminal

instrument, effects

unit, etc. This

Use this terminal to connect

terminal has the

to your ampliﬁer/mixer , etc.

HTS circuit that

keeps sound

texture the same

when the effect is

turned on and off.

POWER DC9V IN terminal

For connecting an AC adapter

with DC 9V center negative

polarity. Requires at least 200mA

of available current.

MIDI IN & OUT/THRU terminals

Used to send/receive MIDI signals

to/from a connected external MIDI

device. The external MIDI controller

can switch PA-1Q series presets

and receive/send preset data from/

to the PA-1Q series.

Recalling a Preset  p.6

Transmitting Data to/from an

External Device  p.7

Adjusting Equalizer

You can create your favorite tone by adjusting various parameters.

To adjust the equalizer:

1. Press the ON/OFF switch to turn on the LED above it.

2. Press the  cursor key switch to select the frequency to be adjusted (blue dot) in the equalizer display.

3. Turn the PARAMETER encoder to adjust the boost amount of the selected frequency.

NOTE

The boost amount of the selected frequency is adjustable in the range of ±12 dB. The selected frequency is shown in the equalizer

display. The boost amount for the selected frequency is shown in the LEVEL display.

Double-clicking the PARAMETER encoder resets the boost amount of the selected frequency to zero. The previous value returns by

double-clicking the encoder again.

To adjust preset's volume:

1. Press the ON/OFF switch to turn on the LED above it.

2. Press the  cursor key switch to select the OUTPUT (green dot) in the equalizer display.

3. Turn the PARAMETER encoder to adjust the volume for the preset.

NOTE

The preset's volume is adjustable from 0 to 127. The preset's volume is shown in the LEVEL display. When all of the frequencies of the

equalizer are set to boost amount 0, unity level is obtained with the LEVEL value 100, and when the value is 127, the volume can be

increased up to +12 dB.

Double-clicking the PARAMETER encoder resets the volume back to 100. The previous value returns by double-clicking the encoder

again.

Editing/Writing Preset Contents

1. Press the ON/OFF switch to turn on the LED above it.

2. Press the  cursor key switch to select the parameter to be adjusted.

3. Turn the PARAMETER encoder to adjust the selected parameter.

4. Press the SAVE switch.

5. The LEVEL display shows the destination preset number.

6. Turn the PARAMETER encoder to select the desired preset number.

7. Press the PARAMETER encoder to store the preset to the selected numbered location.

NOTE

When a preset's parameter is changed, the dot at the PRESET display's lower right corner illuminates. This dot turns off when the

save operation is conﬁrmed by pressing the PARAMETER encoder and the parameters are written to the preset.

If the SAVE switch is pressed again after pressing it, then the write operation is canceled.