- ページ 3

音楽ミキサー Audiodesign PRO PAMX2.62のPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Audiodesign PRO PAMX2.62 6 ページ。 Professional mixers

ページを印刷する

SET UP MEMO

MIC 1

MIC 2

MIC 3

MIC 4

MIC 5

HIGH

12 kHz

MID

2.5 kHz

LOW

80 Hz

AUX

PRE

PAN

MUTE

ALT 3-4

MUTE

CLIP

SOLO

Copy this page to fix the set up

PAMX2. 62

LEFT/

MONO

RIGHT

INPUT

OUTPUT

CD/TAPE

MIC 6

AUX SENDS

24-BIT MULTI-FX PROCESSOR

00 SMALL HALL

03 MID HALL

06 BIG HALL

09 CHURCH

10 SMALL ROOM

13 MID ROOM

16 BIG ROOM

19 CHAPEL

20 SPRING

27 SPRING

30 GATED REV

12V

LINE IN 5/6

LINE IN 7/8

LAM P

400

HIGH

12 kHz

MID

2.5 kHz

AUX SENDS

LOW

80 Hz

SOLO

AUX

SOLO

PRE

2-TR/USB TO MAIN

2-TR/USB

ALT 3-4

PHONES/CTRL R

PAN

BAL

MAIN MIX

MAIN SOLO PFL

SOURCE

7/8

9/10

MUTE

ALT 3-4

SOLO (NORMAL)

PFL (LEVEL SET)

MUTE

CLIP

SOLO

7/8

9/10

ALT

3-4

Service

All Audio Design PRO products have been inspected and tested before leaving the factory and , if

properly used, they will work for many years. However, in case of any problem, please proceed in the

following way:

Contact your dealer and inform about the defect you found

In case it won't be possible to solve the problem with the dealer, the product needs to be returned,

preferably in its original packaging or in a proper packing to protect it during the transport. Purchase

PAM

X 2 .6 2

documents must be produced too.

ULTRALOW-NOISE DESIGN

14-INPUT 2/2-BUS MIC/LINE MIXER

Your dealer will arrange the shipment to our service centre.

WITH PREMIUM MIC PREAMPLIFIERS AND

DIGITAL 24-BIT MULTI-EFFECTS PROCESSOR

USB AUDIO INTERFACE

36 REVERSE

80 CHORUS & REVERB

40 EARLY REFL

82 FLANGER & REVERB

44 AMBIENCE

84 PHASER & REVERB

48 STADIUM

86 PITCH & REVERB

49 AMBIENCE FX

88 DELAY & REVERB

50 DELAY

90 DELAY & GATED

59 ECHO

91 DELAY & REVERSE

60 CHORUS

92 DELAY & CHORUS

66 FLANGER

94 DELAY & FLANGER

70 PHASER

96 DELAY & PHASER

74 PITCH SHIFT

98 DELAY & PITCH

QUICK START:

USB

INTERFA

Start up:

Turn the power switch OFF.

Set "down" all TRIM controls (all counter clockwise ) and FADER ( all down) .

Center EQ controls (High - Mid - Low) and PAN controls (12 hours).

Set all push buttons in their "off" position (button up).

Set "down" all master section controls (counter clockwise and down)

Connections:

PROGRAM

( PUSH )

If you already know how you want to connect the mixer, go ahead and connect. If you prefer to inspect

STEREO AUX RETURNS

operation, please follow these instructions:

Plug a microphone or a mono signal source into one of the mono channels.

TO AUX

SEND 1

or a stereo signal source into one the stereo channels.

Connect MAIN OUTPUTS to an amplifier (XLR Balanced / Jack Balanced).

Turn power switch on. The blue led (POWER) lights up.

MAIN MIX

ALT 3-4

Set the levels:

Push the button "MODE" to use LED level indicators , in PFL mode (Level Set)

Push the button "SOLO " of the channel you intend to set up.

Set the TRIM potentiometer of the channel until the LED indicators (left column) are next to "0" level or

MAX

in any case never over +5 level. Avoid absolutely to reach level

Release button "SOLO" of the channel you have just set up.

Repeat procedure from point 2 to point 4 for each channel you intend to connect

MODE

Mixing:

Set the FADER of each channel at "0" position

Release the button "MODE" to set it in position "SOLO" (NORMAL)

Turn the button "MAIN MIX" to see outlet signal level on the LED indicators.

Turn up "MAIN MIX" to desired level, in relation to the amplifiers / speakers you are using. Preferably,

don't exceed level "0" or "+5" on the LED indicators.

Adjust FADER of each channel to obtain your own mix.

If necessary, adjust tones and repeat above " set levels" procedures

General indications:

The optimum FADER position is near to 0 while the optimum position for the MAIN MIX is the one that

MAIN MIX

don't exceed level 0 / +5 on the LED level indicators.

Check that the level of each power input is the same that you set up during the "set the levels"

operations, even if you have eventually operated on EQ of each channel. If necessary, each channel can be

adjusted even during the performance through TRIM set up and monitored throught the LED indicators. Avoid

absolutely that CLIP indicator of each channel lights up.

In case you intend to connect further sources, please take care to turn down "MAIN MIX" slider

MIXER PROFESSIONALI

+ 10/Clip.

PAMX2

Serie