- ページ 2

セキュリティシステム Addmore ESS260RのPDF インストレーション・マニュアルをオンラインで閲覧またはダウンロードできます。Addmore ESS260R 3 ページ。 Solar charged siren

ページを印刷する

4. USAGE

When installed as part of an ERA alarm system, the siren must be registered to the control panel only.

Connecting to a Control Panel

Press the learn button on the solar siren (0.5 seconds), the

system goes into learn mode after one beep is heard.

Press the 'Arm' button on the control panel/ App.

The wireless siren is paired successfully after a second

beep. If two beeps are heard, the accessory is already linked.

To finish pairing the siren, press the 'Learn' button on

the siren again to exit learn mode after one beep.

The control panel is now armed, press [ ] to disarm the

control panel.

When installed as a siren only alarm system (without a control panel), all of the alarm accessories must be registered

to the siren.

Connecting a Wireless Accessory to the Siren

Press the learn button on the solar siren (0.5 seconds),

the system goes into learn mode after one beep is heard.

Press the test button on the accessory or trigger the

accessory once.

The wireless accessory is learned successfully after a

second beep.

If two beeps are heard, the accessory is already linked.

To finish pairing the accessory, press the learn button

on the siren again to exit learn mode after one beep.

5. INSTALLATION

Remove the fixing screw from

the bottom edge of the siren

housing and carefully remove

the front cover.

Test Mode

Test mode prevents the siren's tamper switch from triggering

an alarm during maintenance or when changing the battery.

When the remote control is connected with the siren, press

[ ] 3 times (within 5 seconds) to enter test mode, the siren

will emit a long beep indicating that the system is now in

test mode. During this period the siren will not alarm but

will beep if the tamper switch or the connected sensors

are triggered.

Press [ ] on the remote control to exit test mode after a

short beep.

The system is now armed. Press [ ] to disarm the system.

Please note: pressing the rear anti-tamper switch 7 times

will also enter test mode.

Please connect the 9V Battery and press the power on/off button.

Please note: after charging the battery for 12-24 hours, please remove the 9V battery.

Hold the mounting plate in

position and mark the positions

of the four mounting holes.

There is a Spirit Level inside

the case to help ensure that

the siren is level.

Enter/Exit learning status using a connected Remote Control

If the siren has been fitted as a standalone system, additional accessories can

easily be learnt to the siren without the need to dismount the siren from the

wall, as follows:

Press [ ] on the remote control 3 times (within 5 seconds) to enter test mode.

Press [ ] 3 times (within 5 seconds) to enter learn mode. A long beep is heard

from the siren indicating that it is in learn mode.

Press the test button on the additional accessory or trigger the accessory once.

The siren will beep again to indicate that the accessory has been successfully

connected with the siren.

Press [ ] on the remote control to exit learn mode, it will emit one beep.

The system is now armed, press [ ] to disarm the system.

The siren arms 15 seconds after the control panel -

please consider this when testing the siren. The siren

will sound and the strobe lights will flash upon alarm

activation. Disarming the system will stop the siren

sounding. If not disarmed, the siren status indicator

will flash once every 2 seconds for one hour (visual

notification of an alarm event).

The 'Arm' button will arm the siren with a 15 second exit delay.

sensors on the 'single delay' will have an entry delay of 15 seconds

before the alarm sounds (unless disarmed by the remote control

during the delay period). Sensors on the 'normal zone' will activate

the alarm without a delay, i.e. the siren will sound immediately.

The siren will sound and the strobe light will flash upon activation

of a connected accessory.

Disarm the system to stop the siren sounding. If not disarmed, the

siren status indicator will flash once every 2 seconds for one hour

(visual notification of an alarm event).

Drill four holes in the wall and

insert the wall plugs. Insert the

screws through the backplate

holes and screw them into the

wall plugs.

Hinge the front cover locating tabs

over the top edge of the backplate

and carefully push the base of the

siren cover into place. Secure the

siren cover in place by refitting the

fixing screw in the bottom edge of

the cover.