- ページ 2
ヒーター Consort LST800EMWIFのPDF インストレーション＆コントロール・マニュアルをオンラインで閲覧またはダウンロードできます。Consort LST800EMWIF 8 ページ。 Quality space heaters
ページを印刷する
2
General safety
Our Low Surface Temperature heaters
have been designed and built to the NHS
requirement for safe surface
temperatures which is that no surface
which can be touched by the user will be
more than 43 degrees C (at a room
temperature of 21 degrees C.) This
means that our Low Surface Temperature
heaters out-perform the European
Standard by a significant margin.
The appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities or
lack of experience and knowledge unless
they have been given supervision or
instruction concerning use of the
appliance by a person responsible for
their safety. Children should be
supervised to ensure that they do not
play with the appliance.
Warning
Do NOT site the appliance in a corner.
•
Do NOT handle the appliance with wet
•
hands.
Do NOT use the appliance in
•
workshops or rooms where excessive
dust is generated or present.
Ensure that nothing is pushed into the
•
air outlet of this appliance.
Do NOT touch outlet grille when the
•
appliance is in use.
Do NOT cover or restrict the appliance
•
when in use.
Do NOT use the appliance if
•
damaged.
Do NOT leave the appliance
•
unattended where young children are
present.
The heater MUST be fully secured in the
•
vertical position before being switched
on.
Connection to the Main Supply
Electrical installation should be carried out by a
competent installer, preferably registered with NICEIC
This heater is fitted with a 3-core mains supply cable and
must be permanently connected to the electricity supply via
a double pole switch having 3mm gap on each pole. There
are no exceptions.
A switched Fused Connection unit to BS.1363. Part 4 is a
recommended mains supply connection accessory to
ensure compliance with safety requirements applicable to
fixed-wiring installation.
Note: When switched on for the first time the appliance may
emit a slight smell. This is purely the evaporation of a fluid
used in the manufacturing process.
WARNING: This appliance must be earthed.
Thermally Operated Cut-Out
The appliance is fitted with a thermally operated cut-out
(TOC). This is a safety device, which switches the heater off
if, for any reason, the appliance overheats. The TOC can
only be re-set after the appliance has cooled down. In
order to re-set the TOC, proceed as follows:
•
Switch off appliance and leave for approximately
10 minutes.
•
Switch appliance back on and the TOC will re-set.
•
Ensure that the appliance is functioning correctly.
If the TOC control operates again, the appliance
should be checked by a competent electrician.
The heater carries a 'Do Not Cover' label to warn the user
that if the appliance is covered, there is a risk of
overheating.
Cleaning
Always disconnect the heater from the mains before
cleaning. The heater should not require any maintenance,
but it is strongly advised that it is kept clean. An occasional
wipe over with a soft cloth is all that should be necessary.
•
Do NOT use metal or furniture polish on any part of the
heater.
•
Do NOT touch the heater with wet hands or in any way
bring water into contact with it.
If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified
person in order to avoid a hazard.
Connection to the WIFI
The heaters only work with a 2.4GHz
WIFI network.
Currently all routers support the 2.4GHz band, as it is an older
standard and has maximum device compatibility. Routers
can also support 5GHz WIFI and are often set up to hide
which frequency band is being used, combine both bands
into a single network name, and assign the band
automatically. A mobile phone could be automatically
connected to the 5GHz network, and this will cause pairing
issues. Routers usually have a setting that gives each band
to have a different network name, which is configurable
through the router's web interface. This allows the phone to
unambiguously select the 2.4GHz network. For full pairing
instructions, see section 9.
66001328 Iss 01