- ページ 4
扇風機 DuraVent DIRECT-TEMP Co-Linear Insert KitのPDF 取付説明書をオンラインで閲覧またはダウンロードできます。DuraVent DIRECT-TEMP Co-Linear Insert Kit 16 ページ。 Selkirk direct vent system
ページを印刷する
WARNING
Failure to follow the installation instructions
could cause FIRE, CARBON MONOXIDE
POISONING, OR DEATH. If you are unsure
of installation requirements, call the Phone
Number listed on the instructions or visit
www.selkirkcorp.com.
Selkirk DIRECT-TEMP Colinear Insert Kit
provides a Vertical Cap with a built-in Co-Lin-
ear Adapter at the base and a baseplate to
serve as a flashing. The Kit also includes 2
Lengths of flexible liner. See Table 1 for more
information.
Selkirk DIRECT-TEMP is designed to be the
vent and air intake system for an approved list
of direct vent gas appliances. It is approved
for use also with Amerivent Direct-Vent.
Selkirk DIRECT-VENT materials, design, and
these instructions have been evaluated and
listed by Underwriters Laboratory Inc.
Contact local building or fire officials about
restrictions and installation inspections in your
area, and obtaining building permits before
beginning the installation.
Do not install Selkirk DIRECT-VENT without
first carefully reading the main instructions and
the appliance manufacturer's instructions. If
you still have any doubt about your ability to
complete the installation in a safe manner
after reading these instructions, arrange for a
professional installation.
Selkirk DIRECT-TEMP is for use only with
appliances that are certified or listed by a major
qualified testing agency, such as AGA, CSA,
OMNI, UL, or Warnock Hersey.
Selkirk warranty coverage will be nulled and
void, and serious fire, health, or other safety
hazards may result from any of the following
actions:
- Installation of any damaged Chimney Liner
System;
- Unauthorized modifications of the Chimney
Liner System;
- Installation of any component part not man-
ufactured or approved by Selkirk.
- Installation other than as instructed by Selkirk
and the appliance manufacturer.
4
ATTENTION:
Always maintain required clearances (air
spaces) to nearby combustibles to prevent a
fire hazards. Be sure to check the appliance
manufacturer's installation instructions for
minimum clearance requirements between
the outer walls of the vent pipe/liner system
and nearby combustible surfaces. Be sure
to check the vent termination clearance re-
quirements from doors, windows, soffits, gas
regulators, and air supply inlets, as specified
in local building codes.
The gas appliance and vent system must be
vented directly to the outside of the building,
and never be attached to a chimney serving a
separate solid fuel or gas-burning appliance.
Each direct vent gas appliance must use it's
own venting system. Common venting are
prohibited.
Always wear eye protection and heavy gloves
for protection.
Exercise extreme caution when using ladders
or on rooftops.
Check overhead for power lines, antennas or
other obstacles.
Make sure the inside of the masonry or facto-
ry-built chimney is large enough to accommo-
date two (2) flex liners (3"/3" or 4"/3").
Make sure the masonry chimney is sound in
construction, clean and free from all loose and
potentially flammable debris. If you find any
cracks, loose or missing bricks or tiles, repair
or replace.
Before the installation of the liners, it is rec-
ommended that the chimney be cleaned by a
certified chimney sweep.
Since chimneys are usually very sooty and
dusty, it is advisable to remove or cover your
furniture, rugs etc. for the duration of the
cleaning and installation of the liner.
Masonry chimneys may take various contours
which the flexible liner will accommodate.
However, keep the flexible liner as straight as
possible, avoid unnecessary bending. Due to
possible snagging, which may result in some
Note: Diagrams & Illustrations Are Not to Scale.