- ページ 2

舶用機器 Apollo REACH WIRELESS RW1500-110APOのPDF クイック・スタート・マニュアルをオンラインで閲覧またはダウンロードできます。Apollo REACH WIRELESS RW1500-110APO 4 ページ。 Open-area wall sounder

ページを印刷する

Apollo REACH WIRELESS RW1500-110APO クイック・スタート・マニュアル

Status LED

The REACH Wireless Open-Area Wall Sounder VAD Base

includes a 360° LED indicator which to indicate status

conditions. See table 1.

Table 1: REACH Wireless Device Status & LED

Indication

Device Status

Tamper Not

Power Up

Power Up (dip-switch ON)

Blinks alternatively green/red four

Entering Wake-Up

Link Success

Enters wake-up mode and signals

Link Failure

'Entering wake-up mode' following

Normal Condition

Activation

Battery Faults

Tamper Fault

Replaced

Tone & Volume Selection DIP Switch Settings

Device Addressing

Device addressing is handled by the REACH Wireless Loop-

Interface device (RW1700-030APO).

Devices are soft-addressed automatically when pairing with

the Loop Interface and can be changed manually. Hard-

addressing using Apollo XPERT cards are not supported.

Table 2: REACH Wireless DIP Switch Functionality

DIP Switch

DIP Switch Group Function

Number

Tone Selection

Volume Selection

High/Low Power LED Output

LED Indication

Tamper

Activated

Blinks green four times

Blinks red four times

times

Blinks green four times, then

repeats

this failure

LED off

Red on

Amber blinking

LED off

every 5s

LED off

Blinks amber two times

Notes

Check Tone Table

(Table 4)

Check Volume

Table (Table 3)

N/A

Table 3: REACH Wireless Volume Table

Volume

High*

Medium High

Medium Low

Low

*EN54-3 certified, for Tone Table (Table 4), see appendix

Communication

REACH Wireless Devices use 'radio-frequency' wireless com-

munication to connect to the Loop-Interface.

The Loop-Interface (RW1700-030APO) translates the wire-

less communication into wired Apollo protocol communica-

tion, with each device addressable individually by the fire

panel. See datasheets for the Loop-Interface for more infor-

mation.

Maintenance and Service

Maintenance must be performed in accordance with all

applicable standards. Clean the detector externally using a

soft damp cloth. For full cleaning and recalibration detectors

should be returned to Apollo Fire Detectors.

Batteries

REACH Wireless devices are supplied with two CR123 bat-

teries, battery A and B. The device switches periodically

between the two batteries on a controlled sequence. For cor-

rect operation of the device, both batteries are required with

adequate capacity reserves.

When battery A reaches a low power threshold, it will trig-

ger a fault. This fault requires both batteries to be replaced

in every instance as both batteries should be discharging

equally.

When one (or both) batteries lack power, the Loop-Interface

receives a low battery message and will signal this event on

its in-built display, as well as relay the low battery message

to the fire control panel. The battery fault will also be sig-

nalled by the device itself through its LED indicators if pro-

grammed (see table 1).

Tamper detection

REACH Wireless devices contain an anti-tamper mechanism.

In the event of removal from its base, it sends a tamper de-

tection message to the Loop-Interface.

Tampering detection is not signalled visually by the device

LED.

EMC Directive 2014/30/EU

REACH Wireless Open-Area Wall Sounder complies with the

essential requirements of the EMC Directive 2014/30/EU,

provided that it is used as described in this datasheet.

A copy of the Declaration of Conformity is available from

Apollo on request.

PP5105/2022/Issue 1

Page 2 of 4

DIP Configuration