- ページ 7

ゲートオープナー Daspi MAU 1400のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Daspi MAU 1400 16 ページ。 Swing gates operator

ページを印刷する

Foresee in the boxes holes "F2" the protective coverings for the

power supply cables

(fig.

3). Put inside of the boxes pins "P1" the

spheres "Sf" so grease the pins "P1" , the spheres "Sf" and the holes

of the levers "L1" and after install the levers "L1"

Block the boxes in the holes with concrete and make sure that the

boxes are perfectly horizontal, check that the pins "P1" are aligned

with the pivots and that the levers "L1" touch the lower border of the

leaves

(fig.

6). Put the gear motors on the bottom of the boxes and

orient them like in the

fig.

1-2, fix them to the tapping-screws with the

nuts "D1"

(fig.

7). Install the transmission levers "L2" making coincide

its holes with the pivots of the levers "L1" and "L3" , fix the supplied

safety screws "V1"

(fig.

8). Install the covers of the boxes checking if

you forgot something's in the same. Aligned the levers "L1" with the

leaves and fix them provisionally to the lower border by welding

9). Release the gear motors like in the par. "Emergency or manual

manoeuvre" and carry out a manual manoeuvre in opening and

closing, to control the correct position of gear motors. Fix definitively

the supports "L1" by strong and good welding.

Never carry out circuitries inside the metal boxes.

Make the circuitry like in the control panel manual and install the

obligatory safety devices. Teach the people intended for the use

of the automation about the controls, safety devices, emergency

manoeuvre and dangerousness deriving from the utilize of the

automation. Compile the technical booklet and fulfil the eventual

obligations deriving from the regulations in force.

To avoid dangerous situations that can cause accident or damages to

things or persons, before starting the opening or closing manoeuvres

of the leaves make sure that the covers are installed and that anyone

is nearby the mechanism in movement and that anything's, as

tools or cable, is inside the boxes. Never carry out any adjustment

operations without box cover or with the gear in working, before to

operate into the boxes make sure that the gear motors operations is

finished and that the power supply is disconnected included possible

batteries.

FIn-MeCC VersIon

The application to the MAU gear motor of the mechanical limit

switches assures an exact and safe stop, of the two leaves, in the

wanted position. Verify to have the right foundation boxes suitable

for the installation of the device: cod. No. DAA22002 BOX FIN-

MECC. Make the installation of the foundation boxes and of the

gear motors as per the standard model. Install the blocks "Bc" , that

assure the closing stop of the leaves, with the screws "Vc" on the

support situated in the exterior side of property

blocks "Bc" the adjust screws "Vr" with blocking nut "D2" screwing

completely, and verifying that the same touch the levers "L1"

Install the special transmission levers "Ba" making coincide its holes

with the pivots of the levers "L1" and "L3" , fix the supplied safety

screws "V1"

(fig.

12). Install on the lever "Ba" the adjusting screws

"Vr" with blocking nuts "D2" screwing completely

Install the boxes covers and conduct the gates leaves in maximal

opening position wished. Cut off the power supply and the boxes

covers. Unscrew the adjust screws "Vr" applied on the levers "Ba"

till it lays on levers "L1" so fix the nuts "D2"

covers and conduct the gates leaves in the closing position wished.

Cut the power supply and the boxes covers. Unscrew the adjust

screws applied on the blocks "Bc" till it lays on levers "L1" so fix the

nuts "D2" (fig.11). Install the boxes covers and carry out a complete

movement of the leaves to verify the correct adjusting of the stops,

in case adjust with the screws "Vr" always cutting the power supply

before.

(fig.

5).

WarnIng

(fig.

10). Install on the

(fig.

13).

(fig.

13). Install the boxes

FINN-MECC device does not replace for any reason and in any case

any safety device necessary for the regulation of the installation

Dl-180 VersIon

The device DL-180 has been applied to the gear motor MAU to allow

openings until 180°. Therefore, it is necessary to check the presence

of enough space for such an opening where the gate is supposed

to work. Verify to have the right foundation boxes suitable for the

device assembling: cod. no. DAA220022 BOX FIN-MECC. Carry out

the installation of the boxes and the gear motors as for the standard

model, installing instead of the standard levers "L1" the levers "Lp"

supplied with the kit

(fig.

Install on the gear motors the pinions "Pm" instead of the standard

levers "L3"

(fig.

"V2" always on the side of the pinions "Pm"

Install the pinions "Pr" on the blocks "D" and fix them with safety

screws "V3"

(fig.

the transmission chain "C" between the levers "Lp" , the pinions "Pr"

and "Pm" , close them with the supplied link

Grease the chains. We recommend to check periodically their state of

Lubrificate, and when necessary grease them.

To avoid dangerous situations that can cause accident or damages to

things or persons, before starting the opening or closing manoeuvres

of the leaves make sure that the covers are installed and that anyone

is nearby the mechanism in movement and that anything's, as tools

or cable, is inside the boxes.

Never carry out any adjustment operations without box cover or with

the gear in working, before to operate into the boxes make sure that

the gear motors operations is finished and that the power supply is

disconnected included possible batteries.

DL-180 device does not replace for any reason and in any case any

safety device necessary for the regulation of the installation.

We garantize the correct functioning of FIN-NECC and DL-180

versions only and exclusively if provided by DASPI and only if

combined with the original control panel.

eMergenCy or Manual ManoeuVre

You have to do the emergency or manual manoeuvre or during the

installation, or only if the automation does not work properly or if

there is not power supply.

Put the supplied key "CHS" in the hole "V" and turn the left leaf

clockwise or the right leaf anticlockwise, to free the gear, so open the

gate manually

(fig.

11).

of the automation, you have to put the leaf in the starting position

(it start automatically). Place the key "CHS" in a safety place known

exclusively from the people intended for the use of the automation.

Switch on the power supply, pay attention that there's nobody where

the gate is moving.

(fig.

14).

14). Fix the blocks "D" on the boxes by the screws

15). Cut the power supply, if it's switch on, and put

(fig.

WarnIng

CUT OFF THE POWEr SUPPLy

17). In order to re-establish the normal functioning

(fig.

15).

16).