- ページ 2

スクラバー Dustbane Hurricane 450 XTTのPDF クイックマニュアルをオンラインで閲覧またはダウンロードできます。Dustbane Hurricane 450 XTT 2 ページ。
Dustbane Hurricane 450 XTT にも：マニュアル・ラピード (2 ページ)

ページを印刷する

DAILY MAINTENANCE

Clean the dirty water tank.

Clean the dirty

Check that the

Clean the dirty

water tank.

detergent outlet filter

water tank.

is clean.

Check that the

brush is clean.

Check that the

squeegee is clean

Check that the

squeegee is clean

Make sure the squeegee is clean

squeegee is clean

and the blades are not

Check that the

squeegee is clean

and the blades are not

and the blades are not worn.

worn.

squeegee is clean

and the blades are not

worn.

and the blades are not

worn.

REPLACING THE SQUEEGEE BLADES

worn.

Open the clip (Ref. 1).

Remove the two blade retainers (Ref. 2) by pushing them outwards then extracting them.

Ref. 1

Remove the two blade retainers (Ref. 2) by pushing them outwards then extracting them.

Remove the blade.

Open the clip (Ref. 1).

Remove the blade.

Reuse the same blade by reversing the edge in contact with the floor until all four edges are worn out, or replace with a new blade, fitting it onto the

Remove the two blade retainers (Ref. 2) by pushing them outwards then extracting them.

Open the clip (Ref. 1).

Reuse the same blade by reversing the edge in contact with the floor until all four edges are worn out, or replace with a new blade, fitting it onto the

screws on the body of the squeegee.

Remove the blade.

screws on the body of the squeegee.

Remove the two blade retainers (Ref. 2) by pushing them outwards then extracting them.

screws on the body of the squeegee.

Reposition the two blade pressing devices by centering the wider part of the slots on the squeegee body fastening pins, then push the blade pressing

Reuse the same blade by reversing the edge in contact with the floor until all four edges are worn out, or replace with a new blade, fitting it onto the

Reposition the two blade pressing devices by centering the wider part of the slots on the squeegee body fastening pins, then push the blade pressing

Remove the blade.

Reposition the two blade pressing devices by centering the wider part of the slots on the squeegee body fastening pins, then push the blade pressing

devices inwards.

screws on the body of the squeegee.

devices inwards.

Reuse the same blade by reversing the edge in contact with the floor until all four edges are worn out, or replace with a new blade, fitting it onto the

Close the hook again.

devices inwards.

Reposition the two blade pressing devices by centering the wider part of the slots on the squeegee body fastening pins, then push the blade pressing

Close the hook again.

screws on the body of the squeegee.

Replace the squeegee on its support, following the instructions described previously.

Close the hook again.

devices inwards.

Replace the squeegee on its support, following the instructions described previously.

Reposition the two blade pressing devices by centering the wider part of the slots on the squeegee body fastening pins, then push the blade pressing

Close the hook again.

devices inwards.

Replace the squeegee on its support, following the instructions described previously.

Open the clip (Ref. 1).

Close the hook again.

Replace the squeegee on its support, following the instructions described previously.

Attaching the brush:

Remove the two blade retainers (Ref. 2) by pushing them

•

rest the brush on the floor in front of the machine. Raise the front of the machine by levering on the handle, then lower it onto the brush, centring it with the brush cover. Action the drive lever repeatedly until the brush

Attaching the brush:

engages..

•

outwards then extracting them.

•

Removing the brush:

engages..

Attaching the brush:

engages..

•

Raise the front of the machine by levering on the handle, then operate the brush lever repeatedly. After operating the lever a few times, the brush is released and falls to the ground.

Removing the brush:

•

Removing the brush:

Remove the blade.

•

Raise the front of the machine by levering on the handle, then operate the brush lever repeatedly. After operating the lever a few times, the brush is released and falls to the ground.

engages..

Attaching the brush:

•

Raise the front of the machine by levering on the handle, then operate the brush lever repeatedly. After operating the lever a few times, the brush is released and falls to the ground.

Removing the brush:

•

Reuse the same blade by reversing the edge in contact with the

Raise the front of the machine by levering on the handle, then operate the brush lever repeatedly. After operating the lever a few times, the brush is released and falls to the ground.

engages..

Removing the brush:

floor until all four edges are worn out, or replace with a new blade,

•

Raise the front of the machine by levering on the handle, then operate the brush lever repeatedly. After operating the lever a few times, the brush is released and falls to the ground.

fitting it onto the screws on the body of the squeegee.

Reposition the two blade pressing devices by centering the wider

part of the slots on the squeegee body fastening pins, then push

the blade pressing devices inwards.

Close the hook again.

Replace the squeegee on its support, following the instructions

PLDC02099

described previously.

PLDC02099

Dustbane Products Ltd., 25 Pickering Pl., Ottawa, ON K1G 5P4

DAILY MAINTENANCE

Check the dirty water tank float

Make sure the lids outer seal is

is undamaged and clean and

Check that the

clean and not damaged. Replace

moves freely on the pin.

brush is clean.

if necessary.

BATTERY

CHARGER ON

BATTERY

BOARD

CHARGER ON

BATTERY

BOARD

CHARGER ON

BOARD

REPLACING THE SQUEEGEE BLADES

•

unscrew the nuts fixing the blade retainers;

REPLACING THE SQUEEGEE BLADES

•

remove the two blade retainers;

REPLACING THE SQUEEGEE BLADES

•

remove the blade;

Ref. 2

•

put the same blade back, reversing the edge in contact with the floor until all four edges are worn, or replace with a new one;

•

put the two blade retainers back on the squeegee and screw up the nuts again;

ATTACHING/REMOVING THE BRUSH

Attaching the brush:

•

rest the brush on the floor in front of the machine. Raise the front of the machine by levering on the handle, then lower it onto the brush, centring

ATTACHING/REMOVING THE BRUSH

engages..

Removing the brush:

ATTACHING/REMOVING THE BRUSH

•

Raise the front of the machine by levering on the handle, then operate the brush lever repeatedly. After operating the lever a few times, the brush

PLDC01986

Check that the

Make sure detergent outlet filter

Check that the

detergent outlet filter

Clean the dirty

detergent outlet filter

is clean and free of debris.

is clean.

water tank.

is clean.

TO CHARGE BATTERIES

Plug in On Board charger to

charge batteries if equipped.

NOTE: Never stop charge until

cycle is complete (green light).

Check that the

squeegee is clean

and the blades are not

worn.

ATTACHING/REMOVING THE BRUSHES

Position the brush underneath the head, in the centre

(single-brush floor scrubber), position the brushes underneath

the head on both sides (double brush scrubber), switch the

machine on.

Press the ON-OFF switch, once after starting the machine releases

brush attachment. The button is only enabled when all the

functions are deactivated (suction motor and brushes).

•

Tel: 1-800-387-8226 Fax: 1-800-363-5309 www.dustbane.ca

DAILY MAINTENANCE

Make sure the brushes/drive

Check that the

Check the dirty water tank float

Check that the

brush is clean.

pad are clean and not worn

is undamaged and clean and

brush is clean.

moves freely on the pin.

out. Replace if necessary.

BATTERY

CHARGER ON

BOARD

REPLACING THE SQUEEGEE BLAD

ATTACHING/REMOVING THE BRUS

Check that t

detergent outle

is clean.