アクセサリー Datalogic 02220のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Datalogic 02220 10 ページ。

ページを印刷する

This product is covered by one or more of the following patents.

European Patent 851,211 B1; 1,111,690 B1; 1,148,346 B1; 1,209,487 B1.

Italian Patent IT 1,321,772.

S5N-Mx SERIES

INSTRUCTION MANUAL

Information on IO-Link communication is available on the last

page of this manual.

CONTROLS

OUTPUT LED (S5N-Mx...B01/C01)

The yellow LED ON indicates that the N.O. (normally open) output

status is closed.

STABILITY LED (S5N-Mx...B01/C01)

The green LED ON indicates that the received signal has a reserve

greater than 30% compared to the output switching value.

TRIMMER (S5N-Mx...B01/C01)

The trimmer can be used to adjust sensitivity; the operating distance

increases turning the trimmer clockwise.

WARNING: The trimmer rotation is limited to 270° by a mechanical stop.

Do not apply excessive torque when adjusting (max 40 Nmm).

INSTALLATION

The sensor can be fixed by means of the M18x1 threaded body through

a  18 mm hole, using the two CH.24 nuts enclosed (22 Nm maximum

tightening torque).

Wide range of accessories available: various orientable fixing brackets

ease the sensor positioning (please refer to the accessories listed in the

general catalogue).

The operating distance is measured from the front surface of the sensor

lens.

C models: To improve the detection, the

object has to be moved closer or further away

from the front surface of the sensor lens.

In case of lateral translation, the object must

move as indicated in the figure.

CONNECTIONS

The connections are compliant to the EN 60947-5-2 standard.

M12 CONNECTOR

10 ... 30 Vdc

N.C. OUTPUT

N.O. OUTPUT/

0 V

IO-Link

AXIAL VERSION

14.5

2.5

TRIMMER

M O D E L S

with trimmer

STABILITY LED

OUTPUT LED

FIBRE OPTIC VERSION

72.5

TRIMMER

54.5

TECHNICAL DATA

S5N-MA AXIAL VERSION

Power supply:

Ripple:

Current consumption

(output current excluded):

Outputs:

Output current:

Output saturation voltage:

Response time:

Switching frequency:

Indicators:

Setting:

Operating temperature:

Storage temperature:

Dielectric strength:

Insulation resistance:

B01: 0.1...3.5 m on R2

Operating distance (typical values):

C01: 0...60 cm

Emission type:

Ambient light rejection:

0.5 mm amplitude, 10 ... 55 Hz frequency, for every axis (EN60068-2-6)

Vibrations:

Shock resistance:

Housing material:

Lens material:

Mechanical protection:

Connections:

Weight:

AtEx 2014/34/EU

I I 3G EX nA II T6 ;

I I 3D EX tD A22 IP67 T85°C

DIMENSIONS

RADIAL VERSION

14.5

TRIMMER

without trimmer

LED STABILITY

LED DI USCITA

14.5

CABLE VERSION

6.2

OUTPUT LED

STABILITY LED

OUTPUT LED

S5N-MR RADIAL VERSION

10 ... 30 Vdc (limit values)

2 Vpp max.

35 mA max.

N.O. and N.C.; PNP or NPN (short-circuit protection)

100 mA max.

2 V max.

0.5 ms (2 ms mod.F01/G00)

1 kHz (250 Hz mod.F01/G00)

OUTPUT LED (YELLOW) excluding mod.G00

STABILITY LED (GREEN) (mod.B01/C01/C21/E01/F01)

POWER ON LED (GREEN) (mod.G00)

sensitivity trimmer (mod.B01/C01/C21/E01/F01/T01)

-25 ... 55 °C

-25 ... 70 °C

500 Vac / 1 min. between electronic parts and housing

>20 M / 500 Vdc, between electronic parts and housing

B01: 0.1...2 m on R2

C01: 0...35 cm

red (630 nm) (mod. E01) / red (660 nm) (mod.B01/T01)

infrared (880 nm) (mod. C01/C21/G00)

according to EN 60947-5-2

11 ms (30 G) 6 shock for every axis (EN60068-2-27)

Nickel-plated brass

PMMA

IP67 Type 1 enclosure

M12 - 4 pole connector

60 g. max. connector vers.

SETTING

Setting of S5N-Mx...B01

Position the sensor and reflector on opposite sides.

Turn the sensitivity trimmer to the maximum position.

Moving the sensor both vertically and horizontally, determine the power on

and off points of the yellow LED (OUT) and then mount the sensor in the

middle of the points defined. Optimum operation is obtained when the

green LED (mod.B01) is ON and the yellow LED is OFF.

B01 models: If necessary reduce sensitivity in order to detect very small

targets. In order to improve alignment, repeat the procedure detailed

above whilst progressively reducing the sensitivity.

M O D E L S

with trimmer

without trimmer

Setting of S5N-Mx...C01

Turn the sensitivity trimmer to minimum: the green LED is ON, the yellow

LED is OFF. Position the target to detect in front of the sensor or of the

fibre terminals. Turn the sensitivity trimmer clockwise until the yellow LED

turns ON (Target detected state, pos.A). Remove the target, the yellow

LED turns OFF. Turn the sensitivity trimmer clockwise until the yellow LED

turns ON (Background detected state, pos.B).

The trimmer reaches maximum if the background is not detected.

Turn the trimmer to the intermediate position C, between the two positions

A and B. The green LED must be ON.

STABILITY LED

Datalogic S.r.l.

Via S. Vitalino 13 - 40012 Calderara di Reno - Italy

Tel: +39 051 3147011 - Fax: +39 051 3147205 - www.datalogic.com

Helpful links at www.datalogic.com: Contact Us, Terms and Conditions,

Support.

The warranty period for this product is 36 months. See General Terms

and Conditions of Sales for further details.

For information about the disposal of Waste Electrical

and Electronic Equipment (WEEE), please refer to the

website at www.datalogic.com.

2007

2019

Datalogic

RIGHTS RESERVED.  Without limiting the rights under copyright, no

part of this documentation may be reproduced, stored in or introduced into

a retrieval system, or transmitted in any form or by any means, or for any

purpose, without the express written permission of Datalogic S.p.A.

and/or its affiliates. Datalogic and the Datalogic logo are registered

trademarks of Datalogic S.p.A. in many countries, including the U.S.A.

and the E.U. All other trademarks and brands are property of their

respective owners. Datalogic reserves the right to make modifications

and improvements without prior notification.

821006311 Rev. B

MIN

MAX



S.p.A.

and/or

its

affiliates

ALL