- ページ 2

ドッキングステーション Datalogic JetのPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。Datalogic Jet 2 ページ。 Vehicle cradle
Datalogic Jet にも：クイック・スタート・マニュアル (2 ページ), ユーザーマニュアル (2 ページ)

ページを印刷する

Mounting with Velcro Adhesive Strips (see Figure 2)

This procedure is suggested when mounting the cradle on flat surfaces:

Select a mounting location allowing an easy access to the cradle connector panel;

Carefully clean the adhesive strip seat of the rear of the cradle (see Figure 1) to remove any

impurities that could reduce adhesion;

Remove the protection film from the adhesive side of two of the available Velcro strips and stick

them on the cradle surface, see Figure 2, A;

Remove the protection film from the adhesive side of the two remaining Velcro strips and stick them

on the vehicle surface (smooth and clean for better adhesion), see Figure 2, B;

Affix the cradle to the vehicle surface.

Mounting with Screws (see Figure 3)

This procedure is suggested when mounting the cradle on curved surfaces. It is possible to use 4

self-tapping screws or 4 screws with nuts according to the user's needs:

Select a mounting location allowing an easy access to the cradle connector panel;

Insert the four screws in the cradle mounting holes, see Figure 3, A;

One or more spacers can be used optionally to compensate for mounting to irregular surfaces, see

Figure 3, B;

Affix the assembly to the vehicle surface by means of the four screws (tighten with nuts if not using

self-tapping screws).

POWERING THE DATALOGIC JET™ VEHICLE CRADLE

Once the cradle has been mounted, it is necessary to prepare the power cable termination to connect the

cradle to the vehicle power source.

−

Brown wire: connect to a V+ (10 to 32 Vdc) vehicle power source;

−

Blue wire: connect to the vehicle ground wire or chassis ground;

−

Green/Yellow wire: not to be connected.

For connection to the vehicle power source it is

possible to use the in-line fuse (with holder)

supplied with the cradle.

Verify that the a 8 A slow-blow fuse is contained

within the holder, then splice it to the end of the

brown wire of the cable. Make the distance

between fuse holder and power connection point as

short as possible and apply a caution label on the

fuse holder.

Once the power cable termination has been

completed, it is possible to connect the Datalogic

Jet™ Vehicle Cradle to the vehicle power.

Figure 4 – Fuse Holder

Brown Wire

Figure 5 – Fuse Holder Connection

INSERTING THE DATALOGIC JET™ INTO THE VEHICLE CRADLE

For correct functioning insert the PDA into the

cradle by lightly pushing it towards the upper part of

the cradle retaining clip. Then, push it down until

the retaining clip clicks.

When the cradle is powered, insert the PDA and

the green LED will turn on. If the PDA is not

inserted, the LED remains off while the cradle is still

powered.

CONFIGURING DATALOGIC JET™ PDA FOR VOCAL COMMUNICATION

By default vocal communication takes place through the Datalogic Jet™ PDA integrated loudspeaker and

microphone. Once inserted into the vehicle cradle, the communication has to be managed by the cradle

itself. Thus, the PDA must be configured through the volume settings applet available in the Windows CE

.NET control panel to correctly manage the communication (refer to the Datalogic Jet™ User's Manual for

more details).

Vocal Communication requires Datalogic Jet™ PDA SW version 1.40 or later.

NOTE

CONNECTION

The Datalogic Jet™ Vehicle Cradle can be connected to a host by means of an RS232 interface.

RS232 Connection

The Datalogic Jet™ Vehicle Cradle can be connected to the host by means of any standard null modem

cable. A 9-pin female D-Sub connector must be connected to the RS232 port of the cradle. Once the host

has been turned on, insert the Datalogic Jet™ PDA into the cradle.

Pin 9 of the Vehicle Cradle RS232 connector (normally not connected in null modem cables), supplies

regulated +5 Vdc ± 5% 500 mA max power.

To Vehicle Battery

Figure 7 - RS232 Connection

Datalogic Jet™ Vehicle Cradle

Standard Null Modem Cable

Click

Figure 6 – Inserting the PDA into the Vehicle Cradle

Host Computer