- ページ 2

アクセサリー Datasensor S62-M2 SeriesのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Datasensor S62-M2 Series 4 ページ。

ページを印刷する

S62...M

Background suppression

INSTRUCTION MANUAL

CONTROLS

OUTPUT LED (yellow)

The yellow LED ON indicates that the N.O. output is closed and the N.C.

output is open.

STABILITY LED (green)

When permanently ON, the green LED indicates a normal operating condition

where the received signal has a safety margin superior to 30% respect to the

output switching value. The sensor is ready to function correctly (stability

condition).

DISTANCE ADJUSTMENT TRIMMER (ADJ.)

A 6-turn trimmer allows the background suppression distance adjustment

through a mechanical variation of the optic triangulation angle.

The operating distance increases, rotating the screws in a clockwise direction.

Please refer to the "SETTING" paragraph for acquisition or setup procedure

indications.

POSITION INDICATOR

This indicator presents a scale numbered from 1 to 6 that allows a precise

adjustment of the suppression distance in the entire operating range.

Please refer to the "SETTING" paragraph for use indications.

TIMER ADJUSTMENT TRIMMER (only. M05/M15/M25/M35 vers.)

This control allows to vary the output delay deactivation from 0 to 1 sec.

Please refer to "TIMER FUNCTIONS" paragraph for use indications.

INSTALLATION

The sensor can be positioned by means

of the three housing's holes using two

screws (M4x25 or longer, 1.5Nm max.

tightening torque) with washers.

Various orientable fixing brackets to

ease

the

sensor

positioning

are

available (please refer to the general

catalogue).

The operating distance is measured

from the front surface of the sensor optics.

The M12 connector can be oriented at two different positions using the

specific fastening spring and rotating the block of 180°.

CONNECTIONS

M12 connector

S62-M0...

Power supply:

Ripple:

Consumption

(output current excluded):

Outputs:

Output current:

Output saturation voltage:

Response time:

Switching frequency:

Emission type:

RED (660 nm)

Spot dimension:

6x6 mm (at 200 mm)

Operating distance (typical values):

30...300 mm

Adjustment:

Multiturn distance adjustment trimmer / Timer adjustment trimmer (only M05/M15/M25/M35 vers.)

Difference (90% white / 4% black):

< 8 %

Hysteresis (90% white):

Indicators:

Operating temperature:

Storage temperature:

Insulating strength:

Insulating resistance:

Ambient light rejection:

Vibrations:

Shock resistance:

Housing material:

Lens material:

Mechanical protection:

Connections:

Weight:

Suppression distance setting

1. Object detection

Position object to detect in front of the sensor at the distance required.

Turn distance adjustment trimmer (ADJ) to minimum: yellow LED OFF and

green LED ON.

Rotate trimmer in a clockwise direction until the yellow LED and green LED

turn ON. Object detection condition (A status of position indicator)

2. Background suppression

Remove object and ensure that the background is in front of the sensor:

yellow LED OFF and green LED ON.

Rotate trimmer in a clockwise direction until the yellow LED and green LED

turn ON: background detection condition (B status of position indicator).

The trimmer reaches maximum level with yellow LED OFF if the background

is outside the operating range.

TECHNICAL DATA

S62-M1...

S62-M2...

10 ... 30 VDC

2 Vpp max.

40 mA max.

PNP or NPN N.O./N.C.; 30 Vdc max. (short-circuit protection)

100 mA (overload and overvoltage protection)

≤ 2 V

500 µs

1 ms

1 kHz

500 Hz

INFRARED (880 nm)

15x15 mm (at 400 mm)

60...600 mm

60...1200 mm

< 12 %

< 25 %

< 5 %

OUTPUT LED (YELLOW) / STABILITY LED (GREEN)

-10 ... 55 °C

-20 ... 70 °C

500 Vac 1 min., between electronics and housing

>20 MΩ 500 Vdc, between electronics and housing

According to EN 60947-5-2

0.5 mm amplitude, 10 ... 55 Hz frequency, for each axis (EN60068-2-6)

11 ms (30 G) 6 shock for each axis (EN60068-2-27)

ABS

PMMA window; PC lens

IP67

2 m cable ∅ 4 mm / M12-4 pole connector

90 g. max. cable vers. / 40 g. max. connector vers.

SETTING

Rotate trimmer in an anticlockwise direction until yellow LED turns OFF

and green LED ON: condition where background is outside operating

range (C status of position indicator).

3. Setting and control

Rotate trimmer in an anticlockwise direction until the indicator reaches

an intermediate point between position A and C.

If position A and C are close to each other, leave trimmer on position C.

The sensor is now ready to function correctly and in stable conditions:

DIAGRAMMA DI RILEVAZIONE

S62-M3...

1,5 ms

330 Hz

200x200 mm (at 2000 mm)

200...2000 mm

(recommended target 400x400mm)

< 30 %

< 20 %

TIMER ADJUSTMENT

TRIMMER (mod.M05/M15/M25/M35)

6.18

10.7

OUTPUT LED

STABILITY LED

TIMER FUNCTION (S62...M05/M15/M25)

The timer function allows to adjust the output deactivation delay when the

object is outside the detection area. The delay extends the output activation

allowing the slower interface systems to detect shorter pulses.

The delay adjustment is carried-out manually using the Timer adjustment

trimmer. Clockwise rotation increase the delay from 0 to a max. 1 sec. value.

EX-II-3-D T6

Temperature class:

Max. Power consumption:

Max. Internal capacitance:

Internal inductance:

DECLARATION OF CONFORMITY

We DATASENSOR S.p.A. declare under our sole responsibility that these products are conform to the

2004/108/CE, 2006/95/CE Directives and successive amendments.

WARRANTY

DATASENSOR S.p.A. warrants its products to be free from defects.

DATASENSOR S.p.A. will repair or replace, free of charge, any product found to be defective during the

warranty period of 36 months from the manufacturing date.

This warranty does not cover damage or liability deriving from the improper application of

DATASENSOR products.

DATASENSOR S.p.A. Via Lavino 265

40050 Monte S. Pietro - Bologna - Italy

Tel: +39 051 6765611

Fax: +39 051 6759324

http://www.datasensor.com

DATASENSOR S.p.A. cares for the environment: 100% recycled paper.

DATASENSOR S.p.A. reserves the right to make modifications and improvements without

prior notification.

DIMENSIONS

4.7

RECEIVER

EMITTER

M12

Ø15

CABLE VERSION

18.4

DISTANCE ADJUSTMENT TRIMMER

POSITION INDICATOR

T6 (<85°C)

1260 mW at 30 Vdc

130 nF

negligible

e-mail: [email protected]

826002872 Rev.C