アクセサリー Datasensor S65-PA-5-ZのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Datasensor S65-PA-5-Z 3 ページ。 Line sensor

ページを印刷する

S65-PA-5-Z

Line sensor

INSTRUCTION MANUAL

CONTROLS

OUTPUT LED

The yellow LED ON indicates that the NO output is closed.

DISPLAY (green-coloured display)

The display indicates the value of the measurement detected [operating mode function].

Please refer to the following paragraphs for the correct indications to follow during the acquisition or

setting phase.

M1, M2 LEDs

The LED couple visualises the operating mode according to the table given below:

OPERATING MODE

Object beg. – Object end

Object centre position

Width measurement

Area

ALARM LED

The blinking of the alarm LED indicates that the received signal is insufficient for the correct sensor

functioning. In this case the "digital alarm" output is activated.

SET PUSH-BUTTON

Pressing the push-button for at least 2 seconds activates the self-setting procedure (2 thresholds =>

2 phases).

A long pressure on the button (at least 6 seconds) allows the user to access into the sensor

parameter setting menu.

Please refer to the following paragraphs for the correct indications to follow during the parameter

setting phase.

+/- PUSH-BUTTONS

Pressing the + or – push-buttons for at least 2 seconds allows the user to access into the manual

adjustment mode of the 2 switching thresholds.

The contemporary pressure on the + and – push-buttons (at least 2 seconds) activates the

acquisition procedure of the working area map.

The contemporary pressure on the + and – push-buttons (at least 6 seconds) activates the setting

procedure of the reflecting tape characteristics.

Please refer to the following paragraphs for the correct indications to follow during functioning.

INSTALLATION

The sensor can be mounted by means of the three housing's holes

using two screws (M4x35 or longer) with washers.

Various orientable fixing brackets to ease the sensor positioning

are available (please refer to the accessories listed in the

catalogue).

The operating distance is measured from the front surface of the

sensor optics.

The M12 connector can be oriented at three different positions

using the specific fastening spring and rotating the block of 180°.

DIMENSIONS

5.5

M1 LED

ALARM LED

M2 LED

OUTPUT LED

A 1 2

OUT

SET

SET PUSHBUTTON

17.05

M1 LED

M2 LED

OFF

M12

DISPLAY

+/- PUSHBUTTON

Power supply:

Ripple:

Consumption (output current excluded):

Outputs:

Serial interface:

SYNC input:

Output current:

Output saturation voltage:

Switching frequency:

Indicators:

Setting:

Data retention:

Operating temperature:

Storage temperature:

Electrical protection:

Operating distance (typical values):

Measurement range:

Minimum object detectable:

Resolution:

Linearity:

Emission type:

Ambient light rejection:

Vibrations:

Shock resistance:

Housing material:

Lens material:

OFF

Mechanical protection:

Connections:

OFF

Weight:

M12 CONNECTOR

Available only for the versions with RS485 serial interface (S65-PA-5-Z09-xxxZ).

NOTE: The wire colours are referred to the cables manufactured according to the European

standard.

The S65-PA-5-Z sensor is a line sensor.

The typical functioning diagram is shown in the drawing given below. The object to detect is placed in

front of the sensor and the reflecting tape (inside the package) behind the sensor. The sensor

illuminated with IR lights the tape and receives the reflected light on a photodiode array. Each object

placed between the reflecting tape and the sensor is naturally detected as a dark spot on a luminous

background.

The sensor has 5 operating modes:

• Object beg.: the position of the first object edge is detected

• Object end: the position of the second object edge is detected

• Object centre: the centre of the object is measured

• Width: the distance between the first and last object edge is measured

• Area: the sum of all the object obscured zones is measured

The following diagram shows the sensor output according to the possible object position inside the

meaurement zone.

First ob. edge

A A A A

B B B B

C C C C

D D D D

E E E E

TECHNICAL DATA

30 Vdc max. (short circuit protection)

4 digit display (GREEN), OUTPUT LED (YELLOW)

2 LEDs (M1, M2) operating mode (GREEN)

0.5 mm amplitude, 10 ... 55 Hz frequency, for each

11 ms (30 G) 6 shock for each axis (EN60068-2-27)

CONNECTION

FUNCTIONING

Last ob. edge

Center

Beg

End

(Beg+End)/2

End

Beg

APPLICATION NOTES

The drawing shows how the same object can generate

different obscured zones if placed in different positions

inside the sensor working zone. The same happens if

the object is placed at different distances.

The "Area" operating mode is particularly sensitve to the

reflecting tape's characteristics and for this reason the

sensor can detect the main specifications of the tape

used (please refer to "Advanced functions" paragraph").

10 ... 30 Vdc limit values

2 Vpp max.

70 mA max.

1 PNP or NPN output

1 PNP or NPN alarm output

4-20mA analogue output

RS485, 9600B, 8, N, 1

PNP

100 mA max.

≤ 2 V

> 130 Hz

1 ALARM LED (GREEN)

+, -, SET push-buttons

non volatile EEPROM memory

-10 ... 55 °C

-20 ... 70 °C

Class 2

200 mm

150 mm

0.9 mm

0.15 mm

1% max.

infared (875nm)

according to EN 60947-5-2

axis (EN60068-2-6)

ABS

Glass window and lenses

IP67 (TYPE 1 ENCLOSURE)

8-pole M12 connector

100 g. max.

Width

Area

End-Beg

End

1023-Beg

1023