MP3プレーヤー Fright Ideas BooTunesのPDF クイック・スタート・マニュアルをオンラインで閲覧またはダウンロードできます。Fright Ideas BooTunes 2 ページ。

ページを印刷する
Quick-Start Guide
BooTunes
MORE INFORMATION ONLINE
This guide covers only the most common features
of the BooTunes. A full manual is available online.
Trigger Input Wiring
PWR
DMX
INPUTS
5 - 24 V DC/AC
BUSY
1
C 1 2 3
4
C
5 6 7 8
2
-
3
+
PRESSURE MAT OR PUSH BUTTON
PWR
DMX
INPUTS
5 - 24 V DC/AC
BUSY
1
2
3
C 1 2 3
4
C
5 6 7 8
-
+
BEAM SENSOR

Power Supply

9 -24
VDC
PWR
BooTu
MP3 PLAYER
WWW.FRIGH
PWR
DMX
BUSY
1
2
PWR
BUSY
PUSH BUTTON
PRESSURE MAT
1
2
SENSOR WIRES
PWR
DMX
BLUE
GND (-)
BUSY
BROWN
12VDC (+)
1
2
3
-
WHITE
RELAY C
BLACK
RELAY N.O.
POWER CAN BE SUPPLIED USING THE BARREL
CONNECTOR OR THE TRIGGER TERMINAL BLOCK.
THESE ARE CONNECTED INTERNALLY.
Connecting the Power Supply
The BooTunes ships with a 12 volt DC 1 amp power
supply. Simply connect it to the barrel connector in
the back.
If you're integrating the BooTunes into a system that
already has a suitable power source, you can
connect that power to the front terminal block.
Same goes if you want to share the BooTunes'
power supply with another device.
-
3
+
The BooTunes power supply must be between 9
and 24 volts DC. It requires about 10mA of current
when it's idle, and 20 when it's playing audio.
DMX
INPUTS
5 - 24 V DC/AC
1
C 1 2 3
4
C
5 6 7 8
2
-
3
+
3
4
5
6
7
EIGHT PUSH BUTTONS
INPUTS
BASE STATION
5 - 24 V DC/AC
C 1 2 3
4
C
5 6 7 8
+
C
N.O.
CONNECT THESE ONLY IF THE BOOTUNES
AND BASE STATION USE THE SAME
VOLTAGE AND THE BASE STATION'S POWER
SUPPLY IS NOT CONNECTED.
WIRELESS TRIGGER

Audio Output

The BooTunes audio output is designed to connect to powered
speakers or external amplifiers.
LINE OUT
AUDIO
LINE OUT
AUDIO
STEREO
PWR
DMX
BUSY
1
C 1 2 3
2
-
3
+
SENSOR WIRES
BLACK
GND (-)
RED
12VDC (+)
WHITE
RELAY C
GREEN
RELAY N.O.
8
INPUTS
C
1
2
RELAY
OUTPUT
POWER
BUTTON
OPTICALLY-ISOLATE CIRCUITS FROM DIFFERENT POWER
SUPPLIES, OR WHEN WIRE LENGTHS ARE EXCESSIVE.
OPTICALLY-ISOLATED INPUT
POWERED SPEAKERS
AMPLIFIER
MONO
INPUTS
5 - 24 V DC/AC
4
C
5 6 7 8
NOTE: PIR SENSORS CAN TAKE UP TO A
MINUTE TO "WARM UP". DURING THIS TIME
THE BOOBOX'S INPUT LIGHT WILL BLINK
AND THE SENSOR WILL NOT RESPOND.
PIR MOTION SENSOR
INPUTS
INPUTS
C
1
2
C
1
2
-
+
-
+
C N.O.
SOLID-
RELAY OUTPUT
STATE
OUTPUT