芝生とガーデン用品 AUSTRAL FOLDAWAY 45のPDF マニュアルをオンラインで閲覧またはダウンロードできます。AUSTRAL FOLDAWAY 45 2 ページ。 Rotary hoists

Your Austral FoldAway Rotary Hoist is designed to last a long time. It is important to follow these instructions to ensure you will

enjoy the benefits of a properly installed Rotary. Incorrect installation could damage your Rotary and/or void your Guarantee.

Contact your State Distributor (details below) if your Austral Rotary Hoist does not function correctly or you require spare parts.

Your Accessory Pack will include:

1 x 8mm x 150mm Galvanized Pin

1 x Ground Socket Cap

4 x Small black end Caps (for FA45 only)

4 x Large black end Caps

Installation Instructions

1. Site

(a) Select a suitable site that allows a minimum of 500mm clearance from the end of

each clothesline Arm. This will allow washing to move freely.

(b) Dig a hole 600mm deep and 200mm in diameter. Backfill the hole with drainage

gravel or stones so the Ground Socket's top lip sits just above ground level (Fig.1).

2. Height Setting

Note: If installing on sloping ground please carefully consider the height setting, giving

thought to the upward pitch of the clothesline Arms, the user's height and whether the

user is likely to stand in one location (ie a path) when hanging washing or move around.

(a) Slide the pre-corded Head Section into the top of the Column, allowing the black plastic Cross (that bolts to the 4 Arms) to

slide down over the Column as far as possible. Stand the Column and Head Section upright and slowly rotate the Head

Section, the locking mechanism will align and the Head Section will drop a short distance. Keep rotating and it will drop a

second time.

(b) The Ground Socket has a series of partially hollowed round holes up the side that correspond to different height settings

(Fig. 1). Slide the Column into the Ground Socket and stand it upright in the hole that has been dug, ensure the lip of the

Socket sits just above ground level.

(c) To raise the Head Section, first remove the Line Retainer (length of Cord with a black plastic hook) that loops around the

Arms holding it together, keep the Line Retainer for later use. Remove any wrapping. Carefully open the Arms part way

and check lines are not caught or twisted (Fig.2). In particular ensure outer lines are not looped around the tips of the

Arms. Push Arms upwards until the Cross meets the black plastic Bush and flip the Latch down to secure them together

(Fig. 3 and 4). Note: If it is very difficult pushing the Cross toward the Bush/Latch then re-check all lines to ensure they are

not wrapped around the end of an Arm. Fit Caps to the end of tubular steel Arms and Stays (FA45 only).

(d) With the Arms raised and hoist wound fully down, give consideration to the users head height and select an appropriate set

of height holes on the Ground Socket (note: hoist can be wound up 270mm from its lowest position. Also, the Arms pitch

up making outer lines higher from the ground). Collapse the Head Section, secure the Arms with the Line Retainer and

remove the Column from the Socket. Place the galvanised metal Pin into one of the selected height holes on the Socket,

use a hammer to punch the Pin through the hole. Remove the Pin and repeat for the hole on the other side of the Socket.

The Pin sets the height for the hoist as well as locking the Column in place.

Fig. 2

FOLDAWAY ROTARY HOISTS

FOLDAWAY 45 & 51

1 x Handle Grip – Black

1 x Handle Shaft – Black

1 x Handle Back Cover – Black

Fig. 3

Lip just above

Fig.1

ground level

Suggested

User Height

1890mm

1840mm

1790mm

1740mm

1700mm

130mm gravel

under Socket

and 50mm up

the sides

200mm min

460mm

600mm