- ページ 2

アンプ AUSTRALIAN MONITOR ACM60のPDF 仕様をオンラインで閲覧またはダウンロードできます。AUSTRALIAN MONITOR ACM60 2 ページ。 60w, 4 channel mixer amplifier
AUSTRALIAN MONITOR ACM60 にも：取扱説明書 (7 ページ)

ページを印刷する

Engineered and Distributed By AUDIO TELEX COMMUNICATIONS PTY LTD (

NSW Tel: (02) 9647 1411 Fax: (02) 9648 3698 VIC Tel: (03) 9890 7477 Fax: (03) 9890 7977 QLD Tel: (07) 3852 1312 Fax: (07) 3252 1237 WA Tel: (08) 9228 4222 Fax: (08) 9228 4233

TAS Tel: (03) 6228 6373 Fax: (03) 6278 1063 SA Tel: (08) 8352 4444 Fax: (08) 8352 4488 Export Enquiries: [email protected]

Power Output

Maximum Load

Power Bandwidth

Frequency Response

Total Harmonic Distortion

Signal To Noise Ratio

Tone Controls

Bass @ 100Hz: Boost +12dB Cut -12dB; Treble @ 10kHz: Boost +9dB Cut -9dB

Inputs

Input Sensitivity

Mic: 1mV @ 200 Ohms; Aux 1-3: 75mV @ 47K Ohms; Aux 4: 300mV @ 47K Ohms

Outputs

Speaker: 100, 70 Volts, 8 Ohms; Tape: 350mV @ 10K Ohms; Line: Balanced 700mV

Phantom Power

Speaker Zone Selection

Speaker zone selector, switches 100V line output to 6 separate zones.

Controls

1 Master gain control, 6 Speaker zone selector, 1 Speaker "all call" selector,

Pre-announce defeat switch, Phantom Power on/off switch (on rear panel)

Indicators

Power Source

Power Consumption

Protection

Soft limiter for overload and overdrive protection, plus AC and DC fuses

Dimensions/Weight

Rack Mounting

Tone Generators

Muting

ARCHITECTURAL AND ENGINEERING SPECIFICATIONS

The mixer amplifier shall have four universal input channels, each comprising of a balanced microphone

input with XLR female sockets and an auxiliary input using dual RCA sockets. The 100 volt line speak-

er outputs should be able to be switched via a six position selector with "all call." A balanced XLR out-

put to drive additional power amplifiers shall also be provided.

The amplifier master section shall include one master gain control, two EQ controls, one with 12dB of

cut and boost at 100Hz and the other with 9dB of cut and boost at 10kHz. Speaker outputs shall be

transformer isolated at 100 volt, 70 volt and 8 ohms. The amplifier must be capable of delivering

60 watts RMS into an 160 ohm inductive load, with less than 0.5% distortion measured at 1kHz and with

system hum and noise less than -74dB.

The amplifier shall be an Australian Monitor Installation Series model ACM60.

), 149 Beaconsfield Street, Silverwater, Sydney, NSW, 2128 Australia

ABN 78 001 345 482

-74dB with all controls at their centre position

Four mic/aux universal inputs with XLR female mic sockets and

18 Volts DC on all Mic inputs (rear panel on/off switch)

An "all call" switch overrides alI zones.

4 Input channel gain controls, 1 Bass control, 1 Treble control,

AC 230/240V - 60Hz, 110V - 50Hz (special) 3 pin IEC connector

88mm H x 480mm W x 330mm D (Chassis Dimensions only). 10kg

Built-in four tone generator module.

Includes Bell, Pre-Announce, Alert and Evac tones

Built-in VOX muting. Channels 1 and 2 will mute channels 3 and 4.

Website: www.australianmonitor.com.au

60 Watts RMS

160 Ohms @ 100 Volts

60Hz - 15kHz < O.5% THD

60Hz - 15kHz (± 3dB)

0.5% @ 1 KHz rated power

dual RCA aux sockets

Power "on" LED

125 Watts

Standard