- ページ 2

エアーコンプレッサー BENDIX BX-2150のPDF クイック・スタート・マニュアルをオンラインで閲覧またはダウンロードできます。BENDIX BX-2150 4 ページ。 Compressor maintenance kit
BENDIX BX-2150 にも：インストレーション・インストラクション (4 ページ)

ページを印刷する

WARNING! PLEASE READ AND FOLLOW THESE INSTRUCTIONS

When working on or around a vehicle, the following guidelines should be observed AT ALL TIMES:

▲ Park the vehicle on a level surface, apply the

parking brakes and always block the wheels.

Always wear personal protection equipment.

▲ Stop the engine and remove the ignition key

when working under or around the vehicle.

When working in the engine compartment,

the engine should be shut off and the ignition

key should be removed. Where circumstances

require that the engine be in operation, EXTREME

CAUTION should be used to prevent personal

injury resulting from contact with moving,

rotating, leaking, heated or electrically-charged

components.

▲ Do not attempt to install, remove, disassemble

or assemble a component until you have read,

and thoroughly understand, the recommended

procedures. Use only the proper tools and

observe all precautions pertaining to use of those

tools.

▲ If the work is being performed on the vehicle's

air brake system, or any auxiliary pressurized air

systems, make certain to drain the air pressure

from all reservoirs before beginning ANY work

on the vehicle. If the vehicle is equipped with a

Bendix

AD-IS

dryer reservoir module, or a Bendix

dryer, be sure to drain the purge reservoir.

▲ F o l l o w i n g t h e v e h i c l e m a n u f a c t u r e r 's

recommended procedures, deactivate the

electrical system in a manner that safely removes

all electrical power from the vehicle.

▲ Never exceed manufacturer's recommended

pressures.

▲ You should consult the vehicle manufacturer's operating and service manuals, and any related literature,

in conjunction with the Guidelines above.

GENERAL

Prior to installation of this kit, park the vehicle on a level

surface and retain by means other than air brakes. Drain

reservoirs to 0 psi. Clean the exterior of the compressor. For

complete compressor removal, refer to the latest revision

of "Caterpillar

Service Manual REG 00914".

GENERAL SAFETY GUIDELINES

TO AVOID PERSONAL INJURY OR DEATH:

air dryer system, a Bendix

AD-9si

▲ Never connect or disconnect a hose or line

containing pressure; it may whip and/or cause

hazardous airborne dust and dirt particles. Wear

eye protection. Slowly open connections with

care, and verify that no pressure is present. Never

remove a component or plug unless you are

certain all system pressure has been depleted.

▲ Use only genuine Bendix

parts, components and kits. Replacement

hardware, tubing, hose, ﬁ ttings, wiring, etc. must

be of equivalent size, type and strength as original

equipment and be designed speciﬁ cally for such

applications and systems.

▲ Components with stripped threads or damaged

parts should be replaced rather than repaired.

Do not attempt repairs requiring machining or

welding unless speciﬁ cally stated and approved

by the vehicle and component manufacturer.

▲ Prior to returning the vehicle to service, make

certain all components and systems are restored

to their proper operating condition.

▲ For vehicles with Automatic Traction Control

(ATC), the ATC function must be disabled (ATC

indicator lamp should be ON) prior to performing

DRM

™

any vehicle maintenance where one or more

air

wheels on a drive axle are lifted off the ground

and moving.

▲ The power MUST be temporarily disconnected

from the radar sensor whenever any tests USING

A DYNAMOMETER are conducted on a vehicle

equipped with a Bendix

DISASSEMBLY (Refer to Figure 1)

1. Remove the discharge line from the discharge port of

the cylinder head and push the discharge line out of

the way.

2. Remove the governor or the air line from the mounting

pad on the head of the compressor. Remove and

discard the governor mounting gasket (1) if the

governor is mounted on the head.

brand replacement

Wingman

system.