- ページ 4

コントロールユニット GAC ESD5528EのPDF マニュアルをオンラインで閲覧またはダウンロードできます。GAC ESD5528E 9 ページ。 Speed control unit
GAC ESD5528E にも： マニュアル (9 ページ)

ページを印刷する
GAC ESD5528E マニュアル
5
ADJUSTmENTS BEFORE ENgINE STARTUP
Make sure the following adjustments are set before starting the engine.
GAIN
STABILITY
SPEED TRIM CONTROL
STARTING FUEL
SPEED RAMPING
6
START ThE ENgINE
The speed control unit governed speed setting is factory set at approximately engine idle speed. (1000 Hz., speed sensor signal or 600 RPM)
If the engine does not start, adjustment of the speed potentiometer may be required.
Crank the engine with DC power applied to the governor system. The actuator will energize to the maximum fuel position until the engine
starts. The governor system should control the engine at a low idle speed. If the engine is unstable after starting, refer to Section 8 ADJUST-
ING FOR STABILITY.
7
gOvERNOR SPEED SETTINg
5.500
(140)
The governed speed set point is increased by clockwise rotation of the
SPEED adjustment control. Remote speed adjustment can be obtained
with an optional 5 kΩ Speed Trim Control potentiometer.
5.000
(127)
8
ADJUSTINg FOR STABIlITy
Once the engine is running at operating speed and at no load, the
following governor performance adjustments can be made to increase
engine stability.
Normally, adjustments made at no load achieve satisfac-
note
tory performance. If further performance improvements
are required, refer to Section 12 TROUBLESHOOTING.
5.500
5.500
(140)
(140)
Parameter
5.000
GAIN
1.
PTIONAL ACTUATOR
5.000
(127)
2.
ABLE SHIELDING TO
(127)
3.
MEET CE DIRECTIVE
4.
*
STABILITY
Follow the same adjustment procedure, steps 1 - 3, as the GAIN parameter.
ACTUATOR
MAGNETIC
PICK-UP
_
+
BATTERY
OPTIONAL ACTUATOR
OPTIONAL ACTUATOR
CABLE SHIELDING TO
*
SEE SPECIFIC ACTUATOR PUBLICATION FOR PROPER
CABLE SHIELDING TO
MEET CE DIRECTIVE
WIRING OF ACTUATOR BASED ON BATTERY VOLTAGE
MEET CE DIRECTIVE
ACTUATOR
ACTUATOR
MAGNETIC
MAGNETIC
PICK-UP
5.750
Middle Position
Middle Position
Middle Position
Full CW (MAX fuel)
Full CCW (fastest)
G A
OVERNORS
MERICA
C
ORP.
SPEED CONTROL UNIT
ESD5500E
MODEL:
S/N :
MADE IN AGAWAM, MA U.S.A.
STARTING
5.750
CAUTION
IMPORTANT:
ENGINE SPEED CONTROL
COMPONENT. WHEN INSTALLING
Speed Adjustment Is a 25
OR SERVICING REFER TO
PRODUCT PUBLICATION.
Turn Potentiometer
-
PICK-UP
G A
OVERNORS
BATTERY
ACTUATOR
G A
MERICA
OVERNORS
A B C D E F G H J
MERICA
C
ORP.
SPEED CONTROL UNIT
SPEED CONTROL UNIT
ESD5500E
MODEL:
ESD5500E
MODEL:
S/N :
S/N :
MADE IN AGAWAM, MA U.S.A.
MADE IN AGAWAM, MA U.S.A.
Rotate the GAIN adjustment clockwise until instability develops.
Gradually move the adjustment counterclockwise (CCW) until stability returns.
CAUTION
CAUTION
Move the adjustment one division further counterclockwise to ensure stable performance (270° potentiometer).
ENGINE SPEED CONTROL
If instability persists, adjust the next parameter.
COMPONENT. WHEN INSTALLING
ENGINE SPEED CONTROL
OR SERVICING REFER TO
COMPONENT. WHEN INSTALLING
PRODUCT PUBLICATION.
OR SERVICING REFER TO
PRODUCT PUBLICATION.
PICK-UP
PICK-UP
ACTUATOR
BATTERY
ACTUATOR
A B C D E F G H J
A B C D E F G H J
S1
FUSE
15A MAX
*
*
PICK-UP
(146)
5.000
(127)
C1 OFF
LEAD CIRCUIT
ON
STABILITY
SPEED
RAMPING
FUEL
5.750
(146)
(146)
5.000
(127)
5.000
(127)
SPEED
+
DROOP
C1 OFF
LEAD CIRCUIT
C1 OFF
C
K
LEAD CIRCUIT
ORP.
ON
STABILITY
STABILITY
GAIN
SPEED
STARTING
ProceDure
SPEED
RAMPING
STARTING
FUEL
RAMPING
FUEL
SPEED
-
+
-
+
DROOP
BATTERY
K
CW
SPEED TRIM
CONTROL - 5K
CW
4
CW
ON
C2
SOFT COUPLING
OFF
E3
E2
GAIN
E1
IDLE
DROOP
IDLE
10V
ON
C2
SOFT COUPLING
AUX
OUTPUT
ON
C2
OFF
ON
L M N P
SOFT COUPLING
OFF
E3
E3
E2
E2
GAIN
E1
E1
IDLE
IDLE
ACCESSORY POWER
SUPPLY
SPEED
ACCESSORY INPUT
DROOP
DROOP
ADD JUMPER FOR 12V
DROOP
IDLE
BATTERY OR ACTUATOR
10V
IDLE
CURRENTS ABOVE 5A
AUX
OUTPUT
10V
K
L M N P
AUX
OUTPUT
GROUND REFERENCE
L M N P
CLOSE FOR DROOP
CLOSE FOR IDLE
ACCESSORY POWER
SUPPLY
ACCESSORY INPUT
ACCESSORY INPUT
ADD JUMPER FOR 12V
ADD JUMPER FOR 12V
BATTERY OR ACTUATOR
CURRENTS ABOVE 5A
BATTERY OR ACTUATOR
CURRENTS ABOVE 5A
GROUND REFERENCE
GROUND REFERENCE
ESD5500E Series Speed Control Unit 9-2020-F PIB1002
CLOSE FOR DROOP
Governors America Corp. © 2020 Copyright All Rights Reserved
CLOSE FOR DROOP
DEAD TIME
COMPENSATION
JUMPER
1.031
SWITCH
(26)
PROFILE
DEAD TIME
Ø0.266
DEAD TIME
COMPENSATION
COMPENSATION
JUMPER
(6,6)
JUMPER
SWITCH
PROFILE
SWITCH
PROFILE
Ø0.266
Ø0.266
(6,6)
(6,6)
WD554
ACCESSORY POWER
SUPPLY
1.0
1.031
(26)
WD5
WD554