ラベルメーカー Dymo RhinoPRO 1000のPDF 使用方法をオンラインで閲覧またはダウンロードできます。Dymo RhinoPRO 1000 2 ページ。 Dymo rhino 1000: user guide
Dymo RhinoPRO 1000 にも：クイック・リファレンス (2 ページ), ユーザーマニュアル (11 ページ), ユーザーマニュアル (5 ページ)

ページを印刷する

Symbols and special characters

International characters

You can create international characters by combining a letter

and a diacritical (accent). Diacriticals available on the keyboard

are ´ ` ¨ and ^. To add a diacritical to a character, enter the

character first, followed immediately by the diacritical. For

example, press 'E' followed by '´' to get é.

To add a diacritical to an existing character, use

place the cursor under the character to be changed, then press

the appropriate diacritical key.

Symbols

Pressing

changes the display to show symbols and

SYM

special characters, some of which are not available direct from

the keyboard. The display will show:

a-o? (or a-r ? where available).

Each letter selects a line of five symbol characters, as shown in

the table below. Note that some of the more complex printed

symbols are represented by simpler symbols in the display.

Press

to cancel or press the letter key required.

DEL

Use

to select a symbol. Press

symbol in the label, or press

to place it and print the label.

DISPLAYED

CHARACTERS

$ ¢ £ F r ¥

b @ & # :

;

" < >

X % *

R C

. . . 3 . . . 4 . . . 5 . . .

. . .

Æ Å Ç Œ Ø

k æ å ç œ ø

Ã Ë Ñ Õ

m ã ë ñ õ

â ê î ô û

ß ¿ ¡

Note: Rows

Á É Í Ó Ú

p, q and r

á é í ó ú

where

available.

ì ò !

Print contrast — may be adjusted by pressing

space key to display five contrast symbols. Use

symbol. Press

again to confirm the setting. The contrast level will

SYM

revert to the mid-setting when the Labelmaker is turned off and on

again.

DYMO 1000

Troubleshooting

No display

• check machine is on

• replace discharged batteries

or use the AC adaptor

• check AC adaptor plugged

in and switched on.

No printing or poor text

• replace discharged batteries

or use the AC adaptor

• check tape cassette

installed correctly and tape

not kinked

• replace the tape cassette.

No response to print key

• label length too short for text

– press

until >

disappears or clear fixed

length

• !!!!! in display indicates a

printer jam. Printing will stop

again to place the

SYM

and the display return to

normal. Open the cassette

compartment and free the

jam.

PRINTED

•

flashing in the display

CHARACTERS

indicates low battery volts.

¢ £ F r ¥

Replace discharged

batteries or use the AC

@ & # :

;

adaptor.

< >

Accessories

X % *

® © ™

12mm (

") cassettes

Black/Clear

Blue/Clear

Red/Clear

Black/White

Blue/White

Red/White

Black/Blue

Black/Red

Æ Å Ç Œ Ø

Black/Yellow

æ å ç œ ø

Black/Green

Replacement Cutter

Ã Ë Ñ Õ

Carrying Case

ë ñ õ

AC Adaptor

ê î ô û

This product is designed to conform with the

following international standards:

¿ ¡

EN 60950

Specification for safety

Á É Í Ó Ú

IEC 950

of information technology

UL 1950

equipment including electrical

é í ó ú

business equipment

EN 55022

Specification for limits and

ò !

Class B

methods of measurement of

radio interference

followed by the

SYM

characteristics of information

to select a

technology equipment.

FCC pt15

Federal communications

Sub pt B

commission radio frequency

Class B

emissions.

Written by

DAW Publications, Cambridge

Power supply

Insert five size AA alkaline or

nickel-cadmium re-chargeable

batteries, observing the polarity

markings.

Re-chargeable batteries must be

charged externally before use.

Connect the AC

adaptor plug here. Use

only the recommended adaptor.

Plugging in the AC adaptor

disconnects the batteries.

Note: Re-chargeable batteries will

not be charged.

45010

45011

45012

Changing the cassette

45013

45014

Ensure tape and ribbon is

45015

taught across mouth of

45016

cassette and tape passes

45017

between

45018

the guide posts

45019

before installing.

15030

15010

40030

DYMO 1000

Electronic Labelmaker

Instructions for Use

Cassette door

To remove the door, press in

where shown below then swing

the door open and lift it away.

When re-fitting, hold the door at

the angle shown below and

engage the tabs on the door in

the slots in the case.

Now close the door, ensuring

that the lever engages with the

ramp on the door as it closes.

Cover

slides

off.

Ensure this lever

engages with ramp on

door when closing.

Lift cassette

straight up

and out.

Label

cutter –

press to

Make sure that

cut off

this switch is set

printed

to the RIGHT

label.

before installing

the cassette. A

notch in the

cassette will fit

over the switch

Ensure tape and ribbon are

when it is set

positioned as shown between

correctly.

print head and pinch roller.

Cleaning

Use a ball pen or

pencil to hold down

interlock button.

Press

Use a cotton

bud and alcohol

to clean both

sides of cutter

blade regularly.

Check and clean

print head and

pinch roller

regularly using

cotton bud and

alcohol ONLY.

Press

here to

open

Push firmly

until cassette

clicks into

place.

Print head

TAPE

CASSETTE

DYMO 1000