- ページ 10

電動工具 Gage Bilt GB704のPDF オリジナル取扱説明書をオンラインで閲覧またはダウンロードできます。Gage Bilt GB704 20 ページ。 Installation tool
Gage Bilt GB704 にも：インストレーション・マニュアル (13 ページ), マニュアル (14 ページ)

ページを印刷する

WARNING:

Tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or

wear. Any repair must be done by qualified personnel trained on Gage Bilt procedures.

WARNING:

Excessive contact with hydraulic oil and lubricants must be avoided.

WARNING:

Maintenance personnel

WARNING:

Disconnect tool from its power source before performing maintenance, cleaning or when replacing worn or

damaged components. Severe personal injury may occur if power source is not disconnected.

WARNING:

Read material Safety Data Sheet documents for all applicable materials

Note:

•

Dispose of hydraulic oil in accordance with manufacture safety datasheet.

•

All tool materials are recyclable except rubber o'rings, seals and wipers.

The performance of any tool depends upon good maintenance practices. Following these minimal requirements for service and care

will extend the life of your tool.

*Only use a clean dry air supply set at 90-100 p.s.i. (6.2-6.9 bar) Max. equipped with a filter-regulator to prevent wear.

* Check tool and nose assembly for damage. (Replace/Repair if necessary). See Overhaul (pgs.13-15) for tool repair.

* Cycle the tool several times to assure there are no leaks during use.

* Keep hydraulic system free of dirt.

*Proper care by operator is necessary in maintaining full productivity and reducing downtime. Read all applicable tool manuals and

nose assembly data sheets prior to operating tools.

*Keep nose assemblies, especially jaws, clean and free of chips and debris. Lube jaws and collet surfaces that jaws ride on with light

machine oil on a daily basis.

*All Screwed End Caps, Base Covers, Air Fittings, Air Actuators, Screws and Nose Assemblies are to be examined at the end of each

working shift to check that they are secure.

*Check tool, all hoses and all couplings daily for damage or air/hydraulic leaks. Tighten or replace (if necessary).

*For a complete overhaul, service tool kit (GB704TK) is recommended (see overhaul pg. 13-15).

•

Keep the hydraulic system full (only use Dexron® III or equivalent) and free of air by using the air bleeder assembly (704153) on a

weekly basis. or as needed. (See Filling and Bleeding procedure pg. 11).

SEE TROUBLESHOOTING (PG. 12) AND OVERHAUL (PGS. 13-15) FOR FURTHER GUIDANCE.

Daily cleaning and lubrication of nose assembly will greatly reduce downtime and increase life of components. Using sewing machine

oil, or an equivalent cleaner/lubricant, follow instructions below.

CLEANING

Clean nose assembly daily or as often as needed.

1. Dip into mineral spirits or similar solvent to clean jaws

and wash away metal chips and debris. DO NOT allow

jaws to come in contact with other solvents. DO NOT let

jaws soak. Dry jaws immediately.

2. Disassemble nose assembly and use a sharp "pick"

to remove embedded particles from grooves of jaws.

TORQUE SPECIFICATIONS

Button Head Cap Screws (A-928) = 40 inch lbs. (4.52 Nm).

Flexlock Nut (400559) = 40 inch lbs. (4.52 Nm).

Packing Plug (704118) = 45 foot lbs. (61 Nm).

End Cap (704112) = 45 foot lbs. (61 Nm).

Button Head Cap Screws (402482) = 35-40 inch lbs. (3.95 - 4.52 Nm) (Do NOT over-tighten).

GB704 S/N: 3213 AND ABOVE

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

DAILY MAINTENANCE

MUST

read and understand all warnings and cautions.

WEEKLY MAINTENANCE

CLEANING AND LUBRICATING PROCEDURE

LUBRICATING

Lubricate nose assembly after each cleaning

and as often as needed.

1. Disconnect tool vacuum line (if equipped).

2. Point nose assembly into oil as shown.

3. Cycle tool 8-10 times and wipe dry.

Image may not

reflect actual

tool

6/11 Rev. 5/22