- ページ 12
電動工具 Gage Bilt GB713のPDF オリジナル取扱説明書をオンラインで閲覧またはダウンロードできます。Gage Bilt GB713 18 ページ。
Gage Bilt GB713 にも： インストレーション・マニュアル (14 ページ), オリジナル取扱説明書 (20 ページ)
ページを印刷する
WARNING:
Only qualified and trained personnel should perform overhaul.
WARNING:
Personnel must read and understand all warnings and cautions.
WARNING:
Tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or
wear. Any repair should be done by qualified personnel trained on Gage Bilt procedures.
WARNING:
Disconnect tool from its power source before performing overhaul. Severe personal injury may occur if power
source is not disconnected.
WARNING:
Excessive contact with hydraulic oil and lubricants should be avoided (See SDS documents for all applicable
materials
WARNING:
When operating, repairing or overhauling tool, wear approved eye protection. Do not look in front of tool or
rear of tool when installing fastener.
WARNING:
Use only Gage Bilt hydraulic hoses and couplings, or equivalent, rated for 10,000 psi. working pressure.
WARNING:
Ensure air hose is securely connected to avoid possible hose whipping (Air Actuated Tools only).
WARNING:
Depress air actuator assy and disconnect from air, with the piston in the rear position, before overhaul.
Severe personal injury may occur if air hose is not disconnected.
rod assy downward with head cylinder removed. Hydraulic oil will eject forcibly from handle assy.
Note:
Dispose of hydraulic oil in accordance with manufacture safety datasheet.
All tool materials are recyclable except rubber o'rings, seals and wipers.
Perform overhaul in a clean, well lit area using care not to scratch or nick any smooth surface that comes in contact with an o'ring. Use of
Lubriplate® (Gage Bilt part no. 402723) or other lubricant is recommended during reassembly to prevent tearing or distorting of o'rings.
The disassembly and re-assembly procedure can be accomplished by utilizing the following instructions and drawings. Use extreme care during
disassembly and re-assembly not to mar or nick any smooth surface that comes in contact with seals. Before installing seals, always apply a
good lubricant, such as Lubriplate, to the surfaces. It is recommended that tool kit (GB740TK) be used to facilitate overhaul. A complete overhaul
can be achieved by the use of Service Kit (713122) which contains a complete set of o'rings, back-up rings, screws, washers and gasket.
Clean parts in mineral spirits or other o'ring compatible solvent being sure to clean o'ring grooves. Inspect components for scoring,
excessive wear or damage.
STEM CATCHER BAG
1.
When tool life is met, drain hydraulic oil from tool and dispose of the hydraulic oil in accordance with SDS datasheet.
2.
Dissassemble tool and remove all rubber o'rings, seals, wipers and hydraulic hoses. All tool materials are recyclable except rub-
ber o'rings, seals, wipers and hydraulic hoses. Dispose of rubber materials in accordance with all environmental regulations
applicable in your area.
GB713
).
704214
704151
POWER CYLINDER TOOL
704149
PISTON ROD WRENCH
(704214 CATCHER BAG SHOWN ABOVE IS SOLD SEPARATELY)
GB740TK Service Tool Kit Includes:
Part No.
Description
704149
Piston Rod Wrench
704150
Packing Plug Wrench
704151
Power Cylinder Tool
704152
Seal Guide
704153
Air Bleeder Ass'y
S1178
Valve Extractor
744251
Valve Spring Installation Tool
744152
Valve Sleeve Removal Tool
OVERHAUL
704152
SEAL GUIDE
704150
704153
PACKING PLUG WRENCH
BLEEDER BOTTLE
TOOL DISPOSAL
12
USE CAUTION
when forcing piston
744251
S1178
VALVE SPRING
VALVE
INSTALLATION TOOL
EXTRACTOR
744152
VALVE SLEEVE
REMOVAL TOOL
7/11 REV 6/16