水ポンプ Hi-Force AHP107のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Hi-Force AHP107 9 ページ。 Air driven hydrotest pumps

ページを印刷する

INSTRUCTION MANUAL – AIR DRIVEN HYDROTEST PUMPS:

Model Series: AHP10.AHP26, AHP36, AHP58, AHP107, AHP187, AHP275, AHP425,

AHP2-036, AHP2-060, AHP2-097, AHP2-144, AHP2-237, AHP3-040, AHP3-060, AHP3-100, ATDP63 ATDP125,

1.0 Inspection of the product upon receipt:

On receipt of the product, visually inspect the

item for any evidence of shipping damage.

Please note shipping damage is not covered

by warranty. If shipping damage is found notify

the carrier immediately and refrain from putting

the product into service. The carrier is

responsible for repair and replacement costs

resulting from damage in transit shipment.

2.0 Safety Precautions:

Read and follow all the instructions and safety

warnings carefully prior to use of the equipment.

Failure to do so could result in equipment

damage or failure of the equipment or personal

injury. Hi-Force will not be held responsible for

any damage to the equipment or personal

injury resulting from unsafe use of the product,

lack of maintenance or incorrect operation. If in

doubt on the correct usage of any Hi-Force

equipment, contact your nearest Hi-Force office

or distributor. If the operator has not been

trained on high pressure hydraulic equipment

and its safe use consult your local Hi-Force sales

office who can offer you training courses for

operators.

All operators should ensure that all necessary

personal protective equipment as specified by

their employer is worn when operating any

hydraulic equipment. Safety shoes, safety

glasses/ visor and protective gloves should be

worn at all times. All relevant risk assessments

should be completed prior to use of the

equipment

Warning: All ancillary equipment to be

used with these ranges of Hydrotest

pumps MUST be rated for use at the same

operating pressure as the pump model to be

used:

Sufficient time should be allocated to

planning your hydraulic system. Make

sure that all the components are fit for the

intended use

DO NOT exceed the rated pressure of the

pump or the rated capacity of the

system to be used.

Hi-Force Limited – Prospect Way – Daventry – Northants NN11 8PL – United Kingdom

Tel: +44(0) 1327 301000: Fax: +44(0) 1327 706555: Website: www.hi-force.com

ATDP216,

AHP SERIES – Hydrotest Pumps:

1.0 General Description:

The Hi-Force AHP range of Hydrotest pumps are

supplied from a range of 8 models with output

pressures ranging from 6 bar(87psi) to 2931bar

(42,500psi) and are suitable for use with various

fluids including water.

2.0 Before operating your Hi-Force Hydraulic

Power Pack please ensure that the following

instructions are carried out.

Check that there is sufficient fluid in the

reservoir. If not, top up with mains

water or suitable hydraulic oil.

Check that the "Pressure Let-Down

Valve" is in the open position (Turn anti-

clockwise).

Close off the "Air Stop Valve". (Turn

anti-clockwise).

Turn the "Air pressure Regulator" anti-

clockwise until the handle becomes

free and easy.

Connect a suitable air supply to the

"Air Supply connection" (3/8" BSP

Female).

Please note that the maximum air

pressure supplied to the Power Pack

should never exceed 100 PSI.

Connect a suitable hydraulic hose

(rigid piping with screwed and coned

connections in case of very high

pressure Power Packs) to the outlet

connection. Please note that the

hydraulic hose or piping together with

adapters and couplings should have a

rated working pressure equal to the

maximum output pressure of the Power

Pack.

Hoses are available from Hi-Force Ltd or your Hi-

Force Distributor suitable for working pressures

up to 30,000 PSI. Above this pressure, stainless

steel piping together with high-pressure fittings

should be used. These are also available from

Hi-Force.