- ページ 7

水ポンプ Hi-Force AHP1121R SeriesのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Hi-Force AHP1121R Series 8 ページ。 Air driven hydraulic pumps
Hi-Force AHP1121R Series にも：取扱説明書 (8 ページ)

ページを印刷する

INSTRUCTION MANUAL – AIR DRIVEN HYDRAULIC PUMPS:

Model Series: AHP1120, AHP1120R, AHP1121, AHP1121R, AHP1122, AHP1122R, AHP1141, AHP1142,

HAP21011, HAP21012, HAP21014, HAP21016, HAP21021, HAP21022, HAP21024, HAP21026, HAP21031,

HAP21032, HAP21034, HAP21036, HAP21041, HAP21042, HAP21044, HAP21046,

11.0 Preparing the Pump for first use:

Immediately after unpacking, examine

the pump for signs of transit damage

and if found contact the shipping

company.

Establish the oil level in the oil reservoir

using the level gauge on the end of

the tank. Depending on the shipping

method used, the reservoir may either

be supplied full or empty. If the

reservoir is empty it must be correctly

filled

before

temporary transit plate which is fitted in

the position of the filler breather cap

(3) by undoing the 3 screws. Fit the filler

breather

cap

using the 3 screws which held the

transit plate.

To fill the reservoir: Remove the filler

cap (3) and fill the tank with clean

HFO46 oil to the upper level indicator

(2).

Connect the air supply to the Motor air

inlet (11). Max inlet pressure 7 bar. It is

recommended

lubricator are incorporated in the air

supply.

Ensure your air supply circuit includes a

ball or sliding valve close at hand,

which can be used to control the air

supply.

Remove hexagon headed plugs and

make hydraulic connections to service

ports (8).These ports have a 3/8" NPT

female thread and the corresponding

male connections should be wrapped

with

PTFE

tape

sealant.

Ensure the lever of the hydraulic

directional control valve (7) is in the

neutral

position.

anticlockwise for models with 2 way

valve (HAP21021, HAP21022, HAP21024,

HAP21026) and the central position for

models

with

(HAP21031,

HAP21032,

HAP20136,

HAP21041,

HAP21044, HAP21046) Where valves

are remotely mounted, ensure these

are adjusted such that pressure will not

build up during the starting operation.

11.1 Operation of the Pump:

Hi-Force does not necessarily know what

equipment this pump will power. Read and

understand

the

appropriate

instructions relating to the equipment in use.

Hi-Force Limited – Prospect Way – Daventry – Northants NN11 8PL – United Kingdom

Tel: +44(0) 1327 301000: Fax: +44(0) 1327 706555: Website: www.hi-force.com

use.

Remove

the

(packed

separately)

that

filter

and

other

suitable

This

fully

way

valves

HAP20134,

HAP21042,

operating

With

all

hydraulic

made

and

operate the directional control

valve (7) if fitted to control the

cylinders or tools in use.

For pumps with 2 way valves:

Turning the lever full clockwise will

supply oil to the service port and

advance the cylinder. Turning the

lever anticlockwise will retract the

cylinder.

For pumps with 3 way valves: Mid

position is the load hold position.

Moving the lever so that it is above

the service port (anti-clockwise)

will supply oil to the port and

advance the cylinder. Moving the

lever away from the service port

will connect the service port to

tank and retract the cylinder.

For pumps with 4 way valves: Mid

position is the load hold position.

Moving the lever so that it is above

either service port will supply oil to

that

port

opposite port to tank.

The

pump

adjustable pressure relief valve (6)

to restrict the out-put pressure to

any desired value up to the

maximum working pressure of the

pump. To increase the relief valve

setting

turn

clockwise. To decrease the relief

valve setting turn the control knob

anticlockwise. Leaving the pump

running for extended periods with

the

relief

cause the oil to overheat.

Ensure that the oil level does not

fall below the minimum level as

shown by the lower indicator (2)

12.0 Maintenance:

In order to ensure the longest service life and

best performance from your pump, regularly

carry out the following routine maintenance.



Inspect the pump for damage after

each use



If a gauge is fitted to the pump ensure

it is regularly checked to ensure it is

within its calibration limits.



Regularly check the oil level in the

pump reservoir by means of the oil

level gauge ( item 2 in the diagrams)



Never run the pump with the oil level in

the reservoir below its bottom limit.

connections

air

motor

running,

and

connect

the

fitted

with

the

control

knob

valve

operating

will