- ページ 5

無停電電源装置 ADELSYSTEM CBI6012AのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。ADELSYSTEM CBI6012A 5 ページ。 Dc ups

ページを印刷する

parameter.

Fig. 9 – SNMP settings

All the fields in the SNMP group of settings allow a maximum of 31

characters, except "System Description" and "System Location", which

allow 255 characters maximum. The actual content of the page depends

on the SNMP version selected (v1, v2c or v3).

Any changes must be confirmed with the confirm button at the bottom of

the page.

Device status

The Dashboard pageshows the main operating parameters of the

device.

Fig. 10 – Device status

System settings

The System page under Configuration shows detailed information on the

device and installed software, to be communicated to the service

technician if requested. Fig. 11 shows example information: the actual

values will be different.

The "device identification" button allows to locate the CBI60 by emitting

a beep and turning on all leds in sequence.

The "System reset" button allows to reboot the device remotely, only if no

battery connected. Current settings will be maintained. Any changes not

saved with the confirm button will be lost.

"System configuration" and "Manual settings" replicate the settings also

accessible on the CBI60 front panel by pressing the CONFIG button

(refer to the relevant section of this manual). Any changes must be

confirmed with the confirm button at the bottom of the page.

"Battery type" selects the battery chemistry from a drop-down list.

If "Configuration mode" is selected Led 4 ON, the following parameters

(Lifetest, Fast charge, UPS enable and Buffering time) cannot be

changed as they are controlled remotely via Modbus or SNMP.

If "Configuration mode" is not selected Led 4 OFF, the following settings

are available: "Lifetest", "Fast charge", "UPS disable" and "Time buffering

time".

The "Charging current" sets the battery charge current limit.

Via Luigi Barchi 9/B – Reggio Emilia 42124 – Italy

Tel. +39 0522 345518 – Fax +39 0522 345551 –

Fig. 11 – Device settings

Saving the customized parameters

To save the changes into the CBI60 non volatile memory press the

confirm button at the bottom of the page.

How to restore default values in the device

(Customer service)

Resetting the customized parameters to their

default values

In case the login user name or password was forgotten, or the TCP/IP

configuration was set incorrectly and the device is no longer reachable,

please follow this procedure to restore the default settings:

•

Turn OFF the device

•

Press the CONFIG button on the front panel and keep it pressed

•

Turn ON the device and continue to keep the button pressed (all

the 9 configuration LEDs will stay ON during this time)

•

After 5 seconds the 4 top configuration LEDs (n. 6 to 9) will blink

alternatively in pairs and the LED 1 will blink slowly showing

"Option 1"

•

Release the button

•

Now click briefly on the button to select one of 4 options, as shown

by the config LEDs 1 to 4. The options are:

1: forces Dynamic (DHCP) IP Addressing Mode

(DHCP) until reboot; the TCP/IP configuration must

be changed on the HTTP server in order to make this

setting permanent.

2: system recovery application, only to be used if

instructed by customer service

3: restore login credentials, TCP/IP and SNMP

settings to factory default

4: restore the complete device to factory settings –

WARNING: all user's settings and logs will be lost,

including the battery type selection.

Confirm the choice by keeping the CONFIG button pressed

for 5 seconds until LEDs 6 to 9 stop blinking.

Technical Data

Please Refer to Data Sheet product

www.adelsystem.com

Instruction Manual CBI60_4

Page 5