- ページ 2

サンダー Dynabrade 53271のPDF 安全・操作・メンテナンスマニュアルをオンラインで閲覧またはダウンロードできます。Dynabrade 53271 4 ページ。 Rebel series 7" & 9" diameter, right angle

ページを印刷する

MAINTENANCE INSTRUCTIONS

Important: To keep tool safe, a Preventative Maintenance Program is

recommended. The program should include inspection of the tool and all

related accessories and consumables, including air lines, pressure regulators,

filters, oilers, etc. (refer to CAGI B186.1 for additional maintenance

information). If accessory or tool breakage occurs, investigate failure to

determine the cause and correct before issuing tool for work. Use the following

schedule as a starting point in developing a Preventative Maintenance

Program. If tool does not operate properly (RPM, vibration, start/stop) after

these scheduled checks or at any time, the tool must be repaired and

corrected before returning tool to use.

INSTALLATION

• To ensure long life and dependable service, use a Closed Loop Air System

and Filter-Regulator-Lubricator (FRL) as diagramed below.

• Each tool should have its own dedicated hose connected to an air supply

FRL. Quick disconnects should be installed at the FRL in an effort to reduce

contamination into the tool. Securely affix all fittings and hose assemblies.

• It is strongly recommended that all Dynabrade rotary vane air tools be used

with a Filter-Regulator-Lubricator to minimize the possibility of misuse due

to unclean air, wet air or insufficient lubrication. Dynabrade recommends

the following: 10690 Air Line Filter-Regulator-Lubricator — Provides

accurate air pressure regulation, two-stage filtration of water contaminants

and micro-mist lubrication of pneumatic components.

• Dynabrade recommends 1 drop of air lube per minute for each 20 SCFM

(example: if the tool specification states 40 SCFM, set the drip rate

on the filter-lubricator to 2 drops per minute). 95842 Dynabrade Air Lube

is recommended.

MAINTENANCE SCHEDULE

Maintenance schedules depend on the type and style of tool. Refer to page

3 to reference symbols associated with specific maintenance items/areas.

Match maintenance schedules accordingly. See page 4 for any additional

maintenance information.

Daily (every 8 hours):

• Inspect tool and accessories for damage or broken parts. Replace items

as necessary to ensure proper operation and safety.

Lubricate motor as recommended. Use 95842 Dynabrade Air Lube

(10W/NR). Apply 1 drop/minute of air lube per 20 SCFM.

• Check air line pressure with a gage. (MAX. 90 PSIG or 6.2 Bar operating

pressure at the air inlet of the tool.)

• Check tool for proper operation: If operating improperly or demonstrates

unusual vibration, the tool must be serviced and problem corrected before

further use.

Every 20 Hours/Once a Week (which ever comes first):

• Measure RPM (speed) by setting air pressure to 90 PSIG (6.2 Bar) at tool

inlet, without accessory mounted, while the tool is running. Using a

tachometer, check spindle speed of the tool. Unless otherwise stated the

no-load speed may not exceed the rated speed. If tool speed exceeds

maximum rated RPM, service as required and correct before use.

• If tool is running too fast: look for worn, damaged or missing governor and

silencer(s). Service as required.

• If tool is running too slow: look for malfunctioning governor, clogged inlet

screen, silencer(s) or air stream. Service as required.

• Governors are not serviceable including the trip disc which activates

the overspeed door. Replace complete 54984 Governor Assemblies,

do not try to repair. Governors should be handled with care. Do not pull on

springs or trip disc in effort to adjust governor.

Note: Special care must be taken when servicing governors. Refer to specific

tool manual for governor instructions and/or speed control devices. Governor

assemblies made from molded plastic components are non-serviceable and

must be replaced.

Every 1,000 Hours (every time tool is rebuilt):

Gears are greased for the life of the tool. Replace if grease is hard

packed or full of debris. Install 14 grams of 96747 Grease on pinion

gear and in cavities on either side of top spindle bearing. Keep

grease out of top spindle bearing pocket as it may prevent ability to

seat bearing in cavity.

REPAIR

• Use only genuine Dynabrade replacement parts to ensure quality. To order

replacement parts, specify Model#, Serial# and RPM of your air tool.

• Mineral spirits are recommended when cleaning the tool and parts. Do

not clean tool or parts with any solvents or oils containing acids, esters,

ketones, chlorinated hydrocarbons or nitro carbons.

• A Motor Tune-Up Kit is available which includes high wear and medium

wear motor parts.

• Air tool markings must be kept legible at all times, if not, reorder housing

and replace. User is responsible for maintaining specification information.

After maintenance is performed on tool, add a few drops of 95842

Dynabrade Air Lube to the tool inlet and start the tool a few times to

lubricate air motor. Verify RPM (per 20 hr maintenance schedule),

vibration and operation.

• The overspeed device has two main components:

- The trip disc which is integral to the governor assembly.

- The overspeed door.

• The overspeed door is held open via an interference fit between the door,

the hinge pin and the rear end plate. If a governor were to fail and allow the

tool to overspeed, the trip disc would expand and close the overspeed door

preventing air from entering the motor. To reset the overspeed door, loosen

and remove the four screws holding the throttle handle and remove the

spacer, motor spring, gasket and governor chamber, if necessary remove

motor. Flip the overspeed door open and gently snap it back into place.

There should be a slight resistance as the door approaches 90°. The door

should be tipped towards the governor by 5° and not wiggle or move freely.

Turn motor by hand to ensure all parts spin freely and have clearance.

Reassemble tool and set air pressure at 90PSIG (6.2 Bar) at tool inlet and

check RPM as indicated. If tool overspeeds again or there is no resistance

when the overspeed door is reset, replace governor assembly, the

overspeed door, the hinge pin and possibly the rear end plate.

HANDLING & STORAGE

• Use of tool rests, hangers and/or balancers is recommended.

• Protect tool inlet from debris (see Notice below).

• Do Not carry tool by air hose or near the tool throttle lever.

• Store accessories in protective racks or compartments to prevent damage.

• Follow the handling instructions outlined in the operating instructions when

carrying the tool and when changing accessories.

• Protect accessories from exposure to water, solvents, high humidity,

freezing temperature and extreme temperature changes.

END OF USE/ DISPOSAL

When tool has reached its end of useful service, disassemble tool into its

primary components (i.e. steel, aluminum and plastic) and recycle or discard

per local, state and/or federal regulations as to not harm the environment.

NOTICE

All Dynabrade air motors use the highest quality parts available and are

manufactured to exacting tolerances. Air motor failures are often traced to lack

of lubrication or unclean air supply. Compressed air can force dirt and other

contaminants into motor bearings causing early failure. Contaminants can score

cylinder wall and vanes resulting in reduced efficiency and power. Our warranty

obligation is contingent upon proper use of our tools. Air motors which have been

subjected to misuse, contaminated air or lack of lubrication will void warranty.