- ページ 2

グラインダー Dynabrade 52213のPDF マニュアルをオンラインで閲覧またはダウンロードできます。Dynabrade 52213 4 ページ。 .5hp/7˚/front exhaust/short shank die grinder
Dynabrade 52213 にも：マニュアル (4 ページ), 操作説明 (4 ページ)

ページを印刷する

Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade

Important Operating, Maintenance and Safety Instructions

Carefully read all instructions before operating or servicing any Dynabrade

Warning: Hand, wrist and arm injury may result from repetitive work motion and overexposure to vibration.

Operating Instructions:

Warning:

Eye, face, sound, respiratory and body protection must be worn while operating power tools. Failure to do so may result in serious

injury or death. Follow safety procedures posted in workplace.

1. With power source disconnected from tool, securely fasten abrasive/accessory on tool.

2. Install air fitting into inlet bushing of tool. Important: Secure inlet bushing of tool with a wrench before attempting to install the air fitting to avoid

damaging valve body housing.

3. Connect power source to tool. Be careful not to depress throttle lever in the process.

4. Air tools are not intended for use in explosive atmospheres and are not insulated for contact with electrical power sources. Sanding/Grinding certain

materials can create explosive dust. It is the employers responsibility to notify the user of acceptable dust levels. Sanding/Grinding can cause sparks

which can cause fires or explosions. It is the users responsibility to make sure the work area if free of flammable materials.

Maintenance Instructions:

1. Check tool speed regularly with a tachometer. If tool is operating at a higher speed than the RPM marked on the tool, the tool should be

serviced to correct the cause before use.

2. Some silencers on air tools may clog with use. Clean and replace as required.

3. Use only genuine Dynabrade replacement parts. To reorder replacement parts, specify the Model #, Serial #, and RPM of your machine.

4. A Motor Tune-Up Kit (P/N 96044) is available which includes assorted parts to help maintain motor in peak operating condition. Please refer to

Dynabrade's Preventative Maintenance Schedule for a guide to expectant life of component parts.

5. It is strongly recommended that all Dynabrade rotary vane air tools be used with a Filter-Regulator-Lubricator to minimize the possibility of misuse due to

unclean air, wet air or insufficient lubrication. Dynabrade recommends the following: 11405 Air Line Filter-Regulator-Lubricator — Provides accurate air

pressure regulation, two-stage filtration of water contaminants and micro-mist lubrication of pneumatic components.

Operates 40 SCFM @ 100 PSIG has 3/8" NPT female ports.

6. Mineral spirits are recommended when cleaning the tool and parts. Do not clean tool or parts with any solvents or oils containing acids, esters

keytones, chlorinated hydrocarbons, nitro carbons or chemicals that have a low flash point (example: WD-40

Safety Instructions:

Products offered by Dynabrade should not be converted or otherwise altered

from original design without expressed written consent from Dynabrade, Inc.

•

Important:

User of tool is responsible for following accepted safety codes such as those published by the American National

Standards Institute (ANSI).

•

Always disconnect power supply before changing abrasive/accessory or making machine adjustments.

•

Inspect abrasives/accessories for damage or defects prior to installation on tools.

•

Please refer to Dynabrade's Warning/Safety Operating Instructions Tag (Reorder No. 95903) for more complete safety information.

All Dynabrade motors use the highest quality parts and metals available and are machined to exacting tolerances. The failure of quality pneumatic motors can

most often be traced to an unclean air supply or the lack of lubrication. Air pressure easily forces dirt or water contained in the air supply into motor bearings

causing early failure. It often scores the cylinder walls and the rotor blades resulting in limited efficiency and power. Our warranty obligation is contingent upon

proper use of our tools and cannot apply to equipment which has been subjected to misuse such as unclean air, wet air or a lack of lubrication during the use

of this tool.

Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within one year from the

date of purchase, all equipment of our manufacture is warranted against defects in workmanship and materials under normal use and service. We shall

repair or replace at our factory, any equipment or part thereof which shall, within one year after delivery to the original purchaser, indicate upon our

examination to have been defective. Our obligation is contingent upon proper use of Dynabrade tools in accordance with factory recommendations,

instructions and safety practices. It shall not apply to equipment which has been subject to misuse, negligence, accident or tampering in any way so as to

affect its normal performance. Normally wearable parts such as bearings, sanding pads, rotor blades, etc., are not covered under this warranty.

Model Number

Motor

1/4" / 6mm

HP (W)

RPM

52210 / 52260

.5 (373)

15,000

52211 / 52261

.5 (373)

18,000

52212 / 52262

.5 (373)

20,000

52213 / 52263

.5 (373)

24,000

Additional Specifications: Air Pressure 90 PSIG (6.2 Bar)

Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade

Notice

Full One Year Warranty

Sound

Maximum Air Flow

Level

CFM/SCFM (LPM)

I.D. Size

78 dB(A)

4/26 (736)

3/8" or 10mm

77 dB(A)

4/28 (793)

3/8" or 10mm

77 dB(A)

4/28 (793)

3/8" or 10mm

82 dB(A)

4/28 (793)

3/8" or 10mm

(PD01•01)

Abrasive Power Tool.

Hose

Air Inlet

Tool

Thread

1/4" NPT

3/8"-24 Male

1/4" NPT

3/8"-24 Male

1/4" NPT

3/8"-24 Male

1/4" NPT

3/8"-24 Male

Weight

Length

Height

Pound (kg)

Inch (mm)

1.7 (0.8)

6 (152)

4-1/2 (114)

1.7 (0.8)

6 (152)

4-1/2 (114)

1.7 (0.8)

6 (152)

4-1/2 (114)

1.7 (0.8)

6 (152)

4-1/2 (114)