- ページ 3

ツール Dynabrade 40601のPDF 安全、操作およびメンテナンスに関する説明書をオンラインで閲覧またはダウンロードできます。Dynabrade 40601 8 ページ。

ページを印刷する

Abrasive Belt/Contact Arm Change Instructions

To Change Belt:

1. Disconnect tool from the power source.

2. Loosen the 15329 Screw and remove the 15312 Belt Guard.

3. Pull back the 15306 Tension Arm and remove the abrasive belt.

4. Install a new abrasive belt, and the 15312 Belt Guard.

Adjust belt tracking by turning 95218 Adjustment Knob to the left or right

accordingly, so as abrasive belt rides evenly over contact arm.

Connect tool to power source.

Housing Angle Adjustment: To pivot the 15372 Belt Housing Assembly, use a 9/64" hex key to loosen the 95311 Screw. Pivot the belt housing assembly to the

desired position and retighten screw.

Installing Side Handle: The 89351 Side Handle may be installed on either side of the gearbox housing, for right or left hand operation. To install, thread side handle

into socket and tighten securely.

Abrasive Types and Cloth Polishing Belts

Aluminum Oxide

The most widely used abrasive grain. This tough durable synthetic is used for

grinding and deburring high carbon steels, general metalworking and for

sanding certain hardwoods.

Ceramic Aluminum Oxide

Synthetic grain two-to-three times tougher than conventional aluminum oxide.

Silicon Carbide

Excellent for sanding primer and sealer. This sharp, fast-penetrating grain is

used for sanding soft materials such as plastics and fibrous wood.

Alumina Zirconia

Effective for coarse stock removal of metal and wood. This synthetic grain has

self-sharpening characteristics and provides continuous new cutting edges for

longer life and greater efficiency.

All abrasive accessories may be found in the most current Dynabrade

Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within one year from the date

of purchase, all equipment of our manufacture is warranted against defects in workmanship and materials under normal use and service. We shall repair or

replace at our factory, any equipment or part thereof which shall, within one year after delivery to the original purchaser, indicate upon our examination to have

been defective. Our obligation is contingent upon proper use of Dynabrade tools in accordance with factory recommendations, instructions and safety

practices. It shall not apply to equipment which has been subject to misuse, negligence, accident or tampering in any way so as to affect its normal

performance. Normally wearable parts such as bearings, contact wheels, brushes, gears, etc., are not covered under this warranty.

To Change Contact Arm Assembly:

1. Disconnect the tool from the power source.

2. L oosen the 15329 Screw and remove the 15312 Belt Guard.

3. Pull back the 15306 Tension Arm and remove the abrasive belt.

4. Loosen the 95218 Adjustment Knob to remove the contact arm assembly.

5. Install the desired contact arm assembly (Ref pg. 6) so that the tab on the

end of the arm faces toward the 15306 Tension Arm.

6. Fasten the contact arm assembly in place with the 95218 Adjustment Knob.

7. Install a new abrasive belt, and the 15312 Belt Guard.

8. Adjust the belt tracking by turning the 95218 Knob.desired position and

retighten screw.

Abrasive Impregnated Non-Woven Nylon

A non-woven synthetic fiber and an abrasive mineral are bonded together to

form a tough, open web that is chemically resistant and long-lasting. This web

design allows controlled conformable contact to workpiece contours, corners

and edges. The product wears away slowly, exposing new abrasive leaving a

uniform, consistent surface. It also conditions surfaces without removing or

damaging the base material and is excellent for deburring, cleaning, blending

and final finishing of metal, wood and plastics. It is available in many forms such

as belts, discs and wheels. Various mineral grades are available

ranging from very coarse to ultra-fine.

Cloth Polishing Belts

Used on power tools in conjunction with Dynuba

result is brilliant cut, color and luster on metals such as stainless steel,

aluminum, copper and brass.

One Year Warranty

(Ref pg. 4)

polishing compounds. The

Catalog and abrasive literature.