- ページ 3
ツール Dynabrade Dynafile 14000のPDF 安全・操作・メンテナンスマニュアルをオンラインで閲覧またはダウンロードできます。Dynabrade Dynafile 14000 12 ページ。 20,000 rpm / versatility kit
Dynabrade Dynafile 14000 にも： 安全・操作・メンテナンスマニュアル (12 ページ)
ページを印刷する
Important: A Preventative Maintenance Program is recommended whenever portable power tools are used.
• Use only genuine Dynabrade replacement parts to insure quality. To order replacement parts, specify Model #, Serial # and RPM
of your air tool.
• It is strongly recommended that all Dynabrade rotary vane air tools be used with a Filter-Regulator-Lubricator to minimize the possibility
fo misuse due to unclean air, wet air or insufficient lubrication. Dynabrade recommends the following: 11405 Air Filter-Regulator-
Lubricator (FRL) – Provides accurate air pressure regulation and two stage filtration of water contaminants. Operates 40 SCFM/1,133
LPM @ 100 PSIG with 3/8" NPT female ports.
• Dynabrade recommends one drop of air lube per minute for each 10 SCFM (example: if the tool specification states 40 SCFM, set the
drip rate on the filter-lubricator to 4 drops per minute). Dynabrade Air Lube (P/N 95842: 1 pt 473 ml) is recommended.
Routine Preventative Maintenance: Check free speed of Dynafile
• Mineral spirits are recommended when cleaning the tool and parts. Do not clean tool or parts with any solvents or oils containing acids,
esters, ketones, chlorinated hydrocarbons or nitro carbons.
• DO NOT clean or maintain tools with chemicals that have a low flash point (example: WD-40
• A Motor Tune-Up Kit (P/N 95600) is available which includes high wear and medium wear motor parts.
• Air tool labels must be kept legible at all times, if not, reorder label(s) and replace. User is responsible for maintaining specification
information i.e.: Model #, S/N, and RPM. (See Assembly Breakdown)
• Blow air supply hose out prior to initial use.
• Visually inspect air hoses and fittings for frays, visible damage and signs of deterioration. Replace damaged or worn components.
• Refer to Dynabrade's Warning/Safety Operating Instructions Tag (Reorder No. 95903) for safety information.
After maintenance is performed on tool, add a few drops of Dynabrade Air Lube (P/N 95842) to the air line and start the tool a few times to
lubricate air motor. Check for excessive tool vibration.
Handling and Storage:
• Use of tool rests, hangers and/or balancers is recommended.
• Protect tool inlet from debris (see Notice below).
• DO NOT carry tool by air hose.
• Protect abrasive accessories from exposure to water, solvents, high humidity, freezing temperature and extreme temperature changes.
• Store accessories in protective racks or compartments to prevent damage.
Model
Motor
Motor
Number
HP (W)
RPM
All Models
.5 (373)
20,000
Additional Specifications: Air Inlet Thread 1/4" NPT • Hose I.D. Size 3/8" (10mm) • Air Pressure 90 PSIG (6.2 Bars)
All Dynabrade motors use the highest quality parts and metals available and are machined to exacting tolerances. The failure of quality
pneumatic motors can most often be traced to an unclean air supply or the lack of lubrication. Air pressure easily forces dirt or water
contained in the air supply into motor bearings causing early failure. It often scores the cylinder walls and the rotor blades resulting in limited
efficiency and power. Our warranty obligation is contingent upon proper use of our tools and cannot apply to equipment which has been
subjected to misuse such as unclean air, wet air or a lack of lubrication during the use of this tool.
Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within one
year from the date of purchase, all equipment of our manufacture is warranted against defects in workmanship and materials under normal
use and service. We shall repair or replace at our factory, any equipment or part thereof which shall, within one year after delivery to the
original purchaser, indicate upon our examination to have been defective. Our obligation is contingent upon proper use of Dynabrade tools in
accordance with factory recommendations, instructions and safety practices. It shall not apply to equipment which has been subject to
misuse, negligence, accident or tampering in any way so as to affect its normal performance. Normally wearable parts such as bearings,
contact wheels, rotor blades, etc., are not covered under this warranty.
Maintenance Instructions
Machine Specifications
Sound
Abrasive Belt Size
Level
Inch (mm)
77 dB(A)
1/8-1/2 (3-13) W x 24 (610) L
One Year Warranty
®
using a tachometer.
Maximum Air Flow
CFM/SCFM (LPM)
4/31 (878)
Notice
(PD02•01R)
3
®
).
Max. SFPM
Weight
Length
(SMPM)
Pound (kg) Inch (mm)
5,800 (1,762)
3.1 (1.4)
14.6 (371)
Height
Inch (mm)
4.0 (115)