- ページ 3

おもちゃ Aircraft in Miniature Limited Historic Wings Wright Flyer 1 1903のPDF 組立説明書をオンラインで閲覧またはダウンロードできます。Aircraft in Miniature Limited Historic Wings Wright Flyer 1 1903 8 ページ。 1:72 metal kit

ページを印刷する

Aircraft in Miniature Limited Historic Wings Wright Flyer 1 1903 組立説明書

This Historic Wings kit is made from etched brass for the main structure, with cast metal detail parts. The

flying surfaces can be covered with the tissue paper supplied, although many modellers may prefer to leave the

structure uncovered to show the details.

Brass components can be soldered together, or joined with cyanoacrylate (SuperGlue) or 5-minute epoxy. If

you have the skills and equipment we recommend soldering.

To remove parts from the etched fret, you can use a pair of side cutters, or put the fret on a ceramic tile, and

press down on each attaching tab with a sharp knife. If you use the 'knife & tile' option, put the attaching tab with

the half-etched side of the tab face down. Whichever method is used, it is necessary to remove the burr of the

attachment tab with a needle file afterwards.

CAUTION - MAKE SURE THE ORIENTATION OF THE WING IS CORRECT BEFORE YOU TWIST

EACH RIB. IF IT IS WRONG, YOU WILL HAVE THE ENGINE ON THE LEFT SIDE, NOT THE RIGHT.

The wings and elevators are etched with integral ribs. Hold the leading or trailing edge in a vice or clamp, and

then hold each rib in turn with a pair of fine flat-nosed pliers, and twist that rib through 90 degrees. When all the

ribs have been turned, clamp the trailing edge, and do the process again.

Where etched parts are joined with two inter-locking slots it may be necessary to enlarge a slot with a needle

file. This is because photo-etching is not an exact process, and sometimes the etching is slightly uneven across a

sheet.

Etched Brass

Fret 1. . . . . . . . . . . . . . 1 off

Fret 2. . . . . . . . . . . . . . 1 off

W10

C 1

Elevator control

Elevator spar (x2)W2

Fuselage frame - left

Fuselage frame - right

Fuselage brace (x2)

Introduction

Parts List

Cast Metal

Engine . . . . . . . . . . . . . . . . . . . . 1 off

Figure - Orville Wright . . . . . . . 1 off

Figure - Wilbur Wright . . . . . . . 1 off

Fuel tank. . . . . . . . . . . . . . . . . . . 1 off

Generator . . . . . . . . . . . . . . . . . . 1 off

Instrument cluster. . . . . . . . . . . . 1 off

Propeller (1 x left, 1 x right) . . . 2 off

Radiator . . . . . . . . . . . . . . . . . . . 1 off

Fret 1

S1 . Strut, interplane-forward (x6)

S2. . . . . Strut, interplane - aft (x6)

W1 . . . . . . . . . . . . . . . . Wing - top

W2. . . . . Wing spar - top, forward

W3 . . . . . . . . . Wing spar - top, aft

Miscellaneous

Instructions . . . . . . . . . . . . . 1 set

Tissue paper . . . . . . . . . . 1 sheet

W4. . . . Wing - top, leading edge

W5 . . . . . . . . . . . Wing - bottom

W8. . . . Wing spar - bottom fwd.

W9 . . . . . Wing spar - bottom aft

W10Wing - bottom, leading edge

6 off