- ページ 4

モビリティ・エイド Days 09 155 3213のPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Days 09 155 3213 17 ページ。 Lightweight rollators

Days 100 Series Lightweight Rollators

Introduction

The Days Lightweight Rollator is a durable walker manufactured from painted aluminium tubing with four solid tyre wheels. It incorporates a

rest seat, storage bag and locking brakes. This walker also has height adjustable handles and can be folded for storage

or transportation.

Before using your new Days Lightweight Rollator, it is essential that you read and fully familiarise yourself with the instructions for use.

Specifications

Overall Height

Overall Width

Overall Depth

Seat Height

Seat Width

Seat Depth

Width between Arms

Backrest Height

Diameter of Wheels

Weight

Max. User Weight

Assembly Instructions

Remove all packaging and examine all parts for signs of shipping

damage. Do not use Rollator if it is damaged or any parts are

missing.

Open the Rollator frame fully. Push the folding hinge until straight

to secure the Rollator in the correct position. Make sure all wheels

make contact with the floor and the Rollator is stable. (See Fig. 1)

Insert a handle with the pre-assembled locking loop brake into

each handle tube. Ensure that the brake cable runs down the

outside of the frame. (See Fig 2)

Depress the pin clips on the backrest and slide it into the tubes at

the front of the Rollator. You should hear a "click" as the pin clips

lock into the securing holes. Ensure both sides of the backrest are

in place with the pin clips protruding through

the holes. (See Fig 3)

Remove the protective plastic covering from the tyres.

Setting the Handle Height

The handles have five settings at 25mm intervals.

To determine the correct height of the handle (See Fig 4);

• Stand upright behind the Rollator with your shoulders

relaxed and arms slightly bent at 15°.

• Set the handle height to be level with your wrists

To adjust each handle to the desired height, line up the holes

appropriately. Slide the bolts through the holes from the inside of

the frame and screw the tightening knobs until secure.

71230 Is5 © Performance Health International Ltd. 2021

102

X-Small

755-875mm

620mm

640mm

505mm

350mm

320mm

460mm

750mm

150mm

6kg

103

105

Small

Medium

790-910mm

825-945mm

605mm

620mm

655mm

540mm

545mm

350mm

320mm

460mm

800mm

200mm

7kg

7.2kg

165

Ensure that the bolt heads are countersunk within the holes, the

tightening knobs are fully tightened and the handles are secure

and stable.

When using the Rollator be aware that stability is dependent on all

four wheels being in contact with a flat surface. Care should be taken

when negotiating uneven ground, inclines and kerbs for example, as

stability will inevitably be reduced.

Hand Brake Operation

(See Fig 5)

The Rollator is fitted with locking brakes for added security. Before

use test the brake by rotating the rear wheels and applying

the brakes.

Note: Always engage and disengage brakes on both sides

To apply the brakes, squeeze both brake handles.

To lock the brakes, push both brake handles down until the click

securely into the locked position.

To release the brakes simply pull up on the brake handles until

they click.

Adjusting the Brake Pressure

If the brakes are too hard to apply, the pressure can be adjusted by

reducing the tension in the spring above the brake shoe.

•

The pressure needed to brake can be adjusted by turning the

knurled knob whilst holding the hexagonal nut below it.

•

Both the knob and nut are located above the brake shoe.

•

Turning the knob anti-clockwise increases the pressure needed

to brake by moving the brake shoe nearer to the wheel and

compressing the spring.

•

Turning the knob clockwise decreases the pressure needed to brake.

106

Large

875-995mm

620mm

670mm

630mm

350mm

320mm

460mm

870mm

200mm

7.3kg

(See Fig. 6)