- ページ 2

煙警報器 Emerald Planet EP-RF-R1のPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。Emerald Planet EP-RF-R1 6 ページ。

ページを印刷する

IMPORTANT SAFETY INFORMATION

1: The test button accurately tests the smoke alarm functions. Do

not use any other test method. Test smoke alarms weekly to

ensure proper operation.

2: If you're sure it isn't a real alarm, open windows or fan the air

around the smoke alarm device to silence it

3: Observe and follow all local and national electrical and building

codes for proper installation.

4: This smoke alarm is designed to be used in residential premises

only. Do not install in non-residential buildings. This smoke alarm

is not a substitute for a complete alarm system.

5: Install a smoke alarm in every room and on every level of the

home. Smoke may not reach the smoke alarm for many reasons.

For example, if a fire starts in a remote part of the home, on

another level, in a chimney, wall, roof, or on the other side of a

closed door, smoke may not reach the smoke alarm in time to

alert household members. A smoke alarm will not promptly

detect a fire except in the area or room in which it is installed.

6: Smoke alarms may not alert every household member every

time. The alarm sound is loud in order to alert individuals to a

potential danger. However, there may be some circumstances

where a household member may not hear the alarm (i.e. outdoor

or indoor noise, deep sleepers, drug or alcohol usage, the hard

of hearing, etc.). If you suspect that this smoke alarm may not

alert a household member, install and maintain specialty smoke

alarms. Every household member must hear the alarm's warning

sound and quickly respond to it to reduce the risk of injury, or

death that may result from fire.

7: Smoke alarms can only activate when they detect smoke or

detect combustion particles in the air. They do not sense heat,

flames, or gas. This smoke alarm is designed to give audible

warning of a developing fire. However, many fires are fast -

burning, explosive, or intentional, and others are caused by

carelessness or safety hazards. In these circumstances, there

may be insufficient smoke to activate the alarm QUICKLY

ENOUGH to ensure safe escape.

8: Smoke alarms have limitations. This smoke alarm is not

foolproof and is not warranted to protect lives or property

from fire. Smoke alarms are not a substitute for insurance.

Homeowners and renters should insure their lives and property.

In addition, it is possible for the smoke alarm to fail at any time.

For this reason, you must test the smoke alarm weekly and

replace unit every 10 years.

BATTERY REPLACEMENT

1: Turn the alarm body anticlockwise and remove the alarm

body from the bracket.

2: Take out the old battery from the battery box.

3: Replace with new batteries into the battery box. Please

ensure the battery polarity is correct (diagram 1).

4: Reattach the alarm body to the bracket and turn the alarm

body clockwise to lock into place.

Press and hold the button to test the unit. The alarm will sound 3

times 1.5 seconds apart indicating a successful test. If there is no

sound, it may indicate a defective alarm or flat battery, you can

refer to "Troubleshooting" for solution or return to your retailer

during warranty period.

NOTE: During testing, because the unit is wirelessly connected

to other smoke alarms, these will resond as well. Once the Test

button is released, the other smoke alarms will stop after 1 minute

DIAGRAM 4

EMERALD PLANET HEAD OFFICE - SYDNEY Unit 2 / 29 Mitchell Road, Brookvale NSW 2100 Australia P 02 9466 6000

DO NOT INSTALL SMOKE ALARMS IN THE

FOLLOWING PLACES

1: Near appliances or areas where normal combustion regularly

occurs (kitchens, near furnaces, open fireplaces, hot water

heaters etc.).

2: In areas with high humidity, like bathrooms or areas near

dishwashers or washing machines. Install at least 10 feet

away from these areas.

3: Near air returns or heating and cooling supply vents. Install

at least 3 feet away from these areas. The air could blow

smoke away from the detector, interrupting its alarm.

4: In rooms where temperatures may fall below 5° or rise above

45°, or in humidity higher than 85%. These conditions could

reduce battery life or cause a false alarm.

5: In extremely dusty, dirty, or insect–infested areas influence

particles interfere with smoke alarm device operation.

OPERATION

TESTING

Test the unit to ensure proper operation by pressing the test

button, this will sound the alarm if the electronic circuitry, horn,

and battery are working. If no alarm sounds, please refer to the

"Troubleshooting" section for solution.

DO NOT USE AN OPEN FLAME TO TEST YOUR ALARM, YOU

COULD DAMAGE THE ALARM OR IGNITE COMBUSTIBLE

MATERIALS AND START A FIRE.

CAUTION: DUE TO THE LOUDNESS (85 DECIBELS) OF THE

ALARM, ALWAYS STAND AT ARMS-LENGTH AWAY FROM

THE UNIT WHEN TESTING. TEST THE ALARM WEEKLY TO

ENSURE PROPER OPERATION. ERRATIC OR LOW SOUND

COMING FROM YOUR ALARM MAY INDICATE A DEFECTIVE

ALARM, PLEASE REFER TO "TROUBLESHOOTING" SECTION

FOR SOLUTION.

NOTE: WEEKLY TESTING IS REQUIRED.

LED INDICATORS

Red LED-Flashing once every 40 seconds: indicates that the

smoke alarm device is operating properly.

Red LED-Flashing when the test button is pressed, or when the

smoke alarm device senses particles of combustion and goes

into alarm (constant pulsating sound), the red LED will flash

once per second. The flashing LED and pulsating alarm will

continue until the air is cleared or test button is released.

Red LED-Alarm silencer (Hush mode) indication: The red LED

will flash once every 8 seconds, indicating the smoke alarm

device is in the alarm silence (Hush) mode.

Low battery indication - An intermittent "chirp" with red

LED flashes once every 40 seconds: indicates that the smoke

alarm device is low on battery, you may press the test button

to pause the alarm for 10 hours, but it will reset automatically

after 10 hours.

Fault indication - The alarm chirp occurs every 40 seconds.

NOTE: WHEN THE UNIT CHIRPS ONCE EVERY 40 SECONDS,

YOU CAN PRESS THE TEST BUTTON TO TEMPORARILY

PAUSE THIS WARNING TONE FOR 10 HOURS. IT CAN STILL

NORMALLY DETECT SMOKE DURING THIS PERIOD, IT ONLY

REMOVES NUISANCE WARNING TONE. YOU CAN REFER TO

"TROUBLESHOOTING" FOR SOLUTION. IF THERE ARE STILL

FAILURES, YOU MUST REPLACE IT WITH A NEW ALARM AT

ONCE OR CONTACT YOUR RETAILER DURING WARRANTY

PERIOD.

ALARM SILENCE (HUSH MODE)

To silence an alarm, push the test button, it will pause the

alarm for approx. 10 minutes. The red LED will flash once every

8 seconds, it indicates the smoke alarm is running in "silence

mode". Smoke alarms are designed to minimise nuisance

alarms. Combustion particles from cooking may set off the

alarm if the alarm is located close to the cooking area. Large