- ページ 15
セキュリティシステム ADEMCO Vista-10PのPDF プログラミング・マニュアルをオンラインで閲覧またはダウンロードできます。ADEMCO Vista-10P 17 ページ。 Alarm control panel
ページを印刷する
Schedules
(installer code + [#] + [6] [4]; master code can only access schedules 01 and events 00-07 )
No.
Event
(see list below)
01 (user)
02 (installer)
Events:
Master/Installer
00 = clear event
01 = device on/off
02 = user access
03 = latch key report
Repeat Options: 0 = none; 1 = repeat weekly; 2 = repeat every other week; 3 = repeat every third week; 4 = repeat every fourth week
Start Scheduling mode by entering installer code + [#] + [6] [4] while in normal operating mode.
NOTE: The master code can only access schedules 01 and events 00-07.
E N T E R S C H E D N O .
0 0 = Q U I T
0 0
E N T E R E V E N T
C L E A R E V E N T 0 0
NOTE: Events 07 and 10
cause the keypad to
beep every 30 seconds
when messages are
displayed. Stop the
beeps by user code +
OFF.
D E V I C E N U M B E R
XX
G R O U P N U M B E R
X
S T A R T
S M T W T F S
0 0 1 0 0 0 0
H H M M A M
S T A R T
S M T W T F S
0 0 1 0 0 0 0
H H M M A M
R E P E A T O P T I O N
0 - 4
X
R A N D O M I Z E
0 = N O 1 = Y E S
X
Device No.
Group No.
for "01" events:
for "02" events:
enter 01-04
enter 1-8
04 = forced STAY arm
05 = forced AWAY arm
06 = auto disarm
07 = display "reminder"
Enter the desired schedule number.
01 = end-user schedule; 02 = installer-only schedule; 00 = exit scheduling mode
[∗] to continue
Enter the desired event number for event you want to occur at a specified time.
Events 10-11 are reserved for the installer only.
00 = clear event
01 = Relay On/Off
02 = User Access
03 = Latch Key Report to Pager (sent to all pagers; message sent is 777-7777; user must be enabled for
paging)
04 = Forced Stay Arming (forced bypass is automatically enabled regardless of setting in field *23)
05 = Forced Away Arming (forced bypass is automatically enabled regardless of setting in field *23)
06 = Auto Disarm
07 = Display "Reminder"
10 = Display custom words (system displays custom words 8, 9, and 10 at defined time; can be used as
installer's reminder message to the end user)
11 = Periodic Test Report
[∗] to continue
This prompt appears if event "1" (relay on/off) was selected, otherwise it is skipped.
Enter the physical device number as programmed in ∗79 Menu Mode.
01-04 = device number; 17, 18 = built-in triggers 1 and 2 respectively
[∗] to continue to the "Start" prompt
This prompt appears if event "2" (user access) was selected. Otherwise it is skipped.
1-8 = group number
[∗] to continue to the "Start" prompt
Enter the event's start time and days of the week to occur.
01-12 = hour; 00-59 = minute; 0 = AM; 1 = PM
Days = position the cursor under the desired days using the [∗] key to move forward, then press "1" to select
the desired day(s)
[∗] to continue
Enter the event's stop time and days of the week to occur.
This entry applies only to the following events: 1 (relay on/off); 2 (user access); 3 (latch key report)
01-12 = hour; 00-59 = minute; 0 = AM; 1 = PM
Days = position the cursor under the desired days using the [∗] key to move forward, then press "1" to select
the desired day(s)
[∗] to continue
Enter the desired repeat option for this schedule.
e.g., To make a schedule that happens everyday you would select all days with a repeat count of 1. To
make a schedule that runs for one week then stops, select everyday with a repeat count of 0.
0 = do not repeat; 1 = repeat schedule weekly; 2 = repeat schedule biweekly (every other week)
3 = repeat every 3rd week; 4 = repeat every 4th week
[∗] to continue
Select whether you want this schedule to start and stop at random times.
If selected, the scheduled start and stop times will vary within 60 minutes of the "hour" time. For example, if
a schedule is set to start at 6:15pm, it will do so the first time 6:15pm arrives, but on subsequent days it will
start anytime between 6:00 and 6:59 p.m.
[∗] to continue
NOTE: Do not use the random option if the start and stop times are within the same "hour" setting, otherwise
unpredictable results may occur (e.g., the randomized stop time may occur before the start time).
Start Time/
Stop Time/
Days
Days
Installer Only
10 = display custom words 8-10
11 = periodic test report
– 15 –
Repeat
Random
(1-4)
(yes/no)