- ページ 5

セキュリティシステム ADEMCO Vista-10PのPDF プログラミング・マニュアルをオンラインで閲覧またはダウンロードできます。ADEMCO Vista-10P 17 ページ。 Alarm control panel

ページを印刷する

∗89

Event Log Full Report Code

See box above *59 for report code entries.

∗90

Event Log Enables

NOTE : System messages are logged when any non-zero

selection is made.

0 = None; 1 = Alarm/Alarm Restore

2 = Trouble/Trouble Restore;

4 = Bypass/Bypass Restore;

8 = Open/Close. Example: To select "Alarm/Alarm Restore",

and "Open/Close", enter 9 (1 + 8); to select all, enter #15.

∗91

Option Selection

Multiple choice example: for AAV (4) + Exit Delay restart (8) enter # + 12.

0 = None

4 = AAV UL: must use ADEMCO UVCM module

8 = Exit Delay Restart/Reset UL: must be disabled

SIA Installations: Exit Delay should be enabled.

∗93

Reports in Armed Period Per Zone

( Also known as Swinger Suppression)

0 = Unlimited Reports; 1 = 1 report; 2 = 2 reports

UL: must be "0"

DOWNLOAD INFORMATION

∗94

Download Phone No.

| | | | | | | | | | | | | | | | | | |

Enter up to 20 digits, 0–9; #+11 for ' '; #+12 for '#'; #+13 for a

2-second pause. Do not fill unused spaces. If fewer than 20

digits, exit field by pressing . To clear entries, press 94 .

UL: downloading may be performed only if a technician is at

the site.

∗95

Ring Count For Downloading

NOTE: Do not enter "0" if using 4285/4286 Phone Module.

0 = Disable Station Initiated Download;

1–14 = number of rings (1–9, # +10 =10, # +11 =11,

# +12 =12, # +13 =13, # +14 =14);

15 = answering machine defeat (# +15 =15).

∗96, *97

Initialize/Reset Defaults

These

(

are commands, not data fields. See page 2

∗98, *99

Exit Commands

(

These

are commands, not data fields. See page 2

PAGER OPTIONS

∗160

Pager 1 Phone No.

| | | | | | | | | | | | | | | | | | |

Enter up to 20 digits. 0–9; #+11 = ' '; #+12 = '#';

#+13 = 2-second pause.

∗161

Pager 1 Characters

Enter the optional prefix characters, up to 16 digits.

0–9; #+11 = ' '; #+12 = '#'; #+13 = 2-second pause.

∗162

Pager 1 Reporting Options

Select from the following options:

0 = no reports sent

1 = Open/closes all users

4 = All alarms and troubles

5 = All alarms / troubles, and open/closes for all users

12 = Alarms / troubles for zones entered in zone list 9

13 = Alarms / troubles for zones entered in zone list 9, and

open/closes for all users

∗172

Pager Delay Option For Alarms

0 = none, 1 = 1 minute, 2 = 2 minutes, 3 = 3 minutes

This delay is for ALL pagers in the system.

NOTE: The delay does not reset for new alarms occurring

while an existing pager delay is in progress.

[00]

[3]

[8]

[1]

[15]

[0]

[3]

MISCELLANEOUS SYSTEM FIELDS

∗177

Device Duration 1, 2

(used in *80 Menu mode-Device Actions 5/6)

0 = 15 seconds

1 = 30 seconds

2 = 45 seconds

3 = 60 seconds

4 = 90 seconds

5 = 2 minutes

∗181

60 Hertz AC Operation

0 = 60 Hz; 1 = 50 Hz

CONFIGURABLE ZONE TYPE OPTIONS

∗182

Configurable Zone Type 90

Enter the appropriate value for each entry, 1-10, based on

the charts provided on the next page. Each entry is the

sum of the values of its selected options

(0-9, #+10=10, #+11=11, #+12=12, #+13=13, #+14=14,

#+15=15).

UL: Do not configure zones as a fire alarm or UL burglar

alarm zone.

∗183

Zone Type 90 Report Codes

IMPORTANT: Use existing Contact ID® codes, if

appropriate, or define unique codes in CID code range

750-789. See note in installation instructions.

90 ALARM ID: XXX

TROUBLE ID: XXX

Enter the desired 3-digit Contact ID® report codes for

alarms and troubles occurring on zones assigned to this

zone type. Enter the codes sequentially (all 6 digits). When

entering digits, [#] moves cursor back, [∗] moves forward.

Press [∗] when done to continue.

KEYPAD OPTIONS

(Options for keypad 1, address 16 are set by the factory and cannot

be changed.)

NOTE: Each keypad must be assigned a unique address.

)

Keypads programmed with the same address will give

unpredictable results.

∗190

)

Keypad 2 Device Address 17

Enable: 0 = disabled; 1 = enabled

Sound: 0 = no suppression

1 = suppress arm/disarm and E/E beeps

2 = Suppress chime beeps only

3 = suppress arm/disarm, E/E, and chime beeps

∗191

Keypad 3 Device Address 18

∗192

Keypad 4 Device Address 19

∗193

Keypad 5 Device Address 20

∗194

Keypad 6 Device Address 21

∗195

Keypad 7 Device Address 22

∗196

Keypad 8 Device Address 23

∗197

Exit Time Display Interval

0 = no display; 1-5 = seconds between display refresh

∗199

ECP Fail Display

0 = 3-digit display ("1" + device address)

1 = 2-digit fixed-display as "91"

– 5 –

[0] [0]

6 = 2-1/2 min

#+11 = 7 min

7 = 3 min

#+12 = 8 min

8 = 4 min

#+13 = 10 min

9 = 5 min

#+14 = 12 min

#+10 = 6 min

#+15 = 15 min

[0] [0]

Enable Sound

[0] [0]

[0]