- ページ 2

スピーカー DaytonAudio CONTRACTOR SeriesのPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。DaytonAudio CONTRACTOR Series 2 ページ。 In-wall speaker
DaytonAudio CONTRACTOR Series にも：ユーザーマニュアル (4 ページ), ユーザーマニュアル (2 ページ)

ページを印刷する

Congratulations on the purchase of your Dayton Audio

These speakers were manufactured with high quality components and engineered to deliver superior

sound performance. Like many of the products sold by Dayton Audio

designed for ease of installation. Please read through the instructions completely before you begin

your installation.

1) Parts Inventory

Your In-Wall kit should include the following:

• 1 pair of Dayton Audio

In-Wall Speakers with Grills

• 1 pair of cardboard mounting/paint masking templates

2) Installation Tools

You can install the Dayton Audio In-Wall speakers with the following tools:

• Pencil

• #2 Phillips screwdriver

• Masking tape

• Wire cutters & wire strippers

• Drill & drill bits

• Small level**

• Utility knife

• Stud finder**

• Keyhole saw*

* Recommended for use if installing in plaster walls.

** Optional tools to make the installation easier.

3) Speaker Location

To achieve the best performance from your Dayton Audio

select the location for installation.

Your in-wall speakers should be installed 5 to 8 feet

apart to ensure proper stereo imaging. If possible, mount

each speaker the same distance from the corners on a

common wall. Keep the speakers at least 2 feet away from

the corners of the room to avoid overemphasized bass

reproduction.

The speakers should be located so that the tweeter height

is at the same level, or slightly above the listener's ear. You

must now decide whether the primary listening will be done

standing or in a seated position. Remember, for the best

stereo imaging, the listening position should be directly in-between the speakers with the tweeters

at ear level.

4) Speaker Installation

Once you have selected the location for your speakers, you are now ready to install them.

CAUTION: Be certain that there are no electrical wires, water pipes, or heating ducts in the

planned installation area before you start drilling or cutting into the wall. If there is an

electrical outlet nearby, turn off the circuit breaker to avoid possible injury.

The in-wall speakers are designed to be mounted to the wall area between the studs. Once you

have selected your location, the next step is to be sure you are between the studs. By tapping on

the wall, you will hear a hollow sound when between two studs and a sharper, more solid sound

when right on top of, or close to a stud. An easier, more accurate method for finding the location of

wall studs is to use a stud finder.

Once you have established that your chosen location is between two studs and that there are no

obstructions in the wall, tape your speaker template to the wall and lightly trace around the inside

opening with a pencil. To ensure that your speaker template is straight, you may want to use a level

before you mark the wall.

Contractor Series In-Wall Speaker System.

, these in-wall speakers were

speakers, it is important to carefully

Drill a 1" hole in the center of the template outline. Next, using a piece of stiff wire (a coat hanger

works well), bend it 8" from the end at a 90 degree angle. Insert the bent part of the coat hanger

into the 1" hole and rotate the wire in a complete circle to check for obstructions. If the wire hits

a stud on either side, reposition your template to the left or right and re-do the light pencil outline.

Keep the pilot hole within the template outline.

If the walls are made of drywall, simply cut the marked area with your utility knife. If your home has

plaster walls, then you will need to drill pilot holes at the four corners of the template outline, and cut

the speaker opening using a keyhole saw.

Check the speaker opening by placing one of the speakers into the hole. The speaker should fit

loosely into the hole.

Repeat these steps for the other speaker.

5) Speaker Cable

Don't compromise sound quality by using thin, inexpensive speaker wire, we recommend using a

high quality oxygen free copper speaker cable. For runs less than 50 feet we recommend 16 gauge

cable, and for longer runs we recommend 14 gauge or larger cable. Most municipalities require the

use of CL2 rated speaker cable for installation in walls and ceilings. Leave enough speaker cable so

you can stand comfortably on the floor or ladder while connecting the speaker cable to the speakers.

Speaker Connection

Remove about 8" of the cable jacket to expose the

inner conductors. Strip 1/4" of insulation from each

conductor and connect to the speaker terminals.

When connecting the wires to the speakers, be sure to

observe proper polarity. Most CL2 rated speaker cable

will have red and black conductors so you will connect

the red wire to the red speaker terminal and the black

wire to the black speaker terminal.

7) Final Installation

To install the speakers into the wall, remove the

grills. This will give you access to the mounting

screws. Turn the mounting clamps so they are

positioned as in the illustration, this will allow the

speakers to clear the hole for installation. Insert

the speaker into the hole, and tighten the mounting

screws. As you turn each screw, the mounting clamps

will rotate outward to engage the wall material.

8) Painting Speakers

If you choose to paint the speaker grill Do not try to paint the grill while it is on the speaker.

The grill should always be painted separately. Do not apply heavy coats of paint that might block the

perforations in the grill.

9) Troubleshooting

Should your speakers not work properly, check the following:

No sound from speakers:

• Most stereo receivers have an A/B speaker selector switch. Make certain that this switch

is in the proper position.

• Mute feature is activated.

One speaker is playing while the other is not:

• Check the balance control on the receiver. Make sure it is centered.

• Loose connection at either the receiver or the speaker. Double check connections.

• Bad speaker cable. Replace suspect speaker wire.

Receiver cuts on and off:

• This could be caused by a short circuit between the positive and negative leads. Check

the connections at the back of the receiver, and then at the speaker. Make sure that no

strands of wire from one connector are touching the other connector.

10) Caring For Your In-Wall Speakers

The two most common ways that in-wall speakers are permanently damaged:

1) Not enough power at higher volumes.

2) Too much power at higher volumes.