- ページ 2

安全装置 GREATLAND Rescue Laser FlareのPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。GREATLAND Rescue Laser Flare 2 ページ。

ページを印刷する

Assembly and Operation

1. To assemble, unscrew end cap. Insert two 1.5-volt AA batteries and

then screw on end cap.

2. Point the light output end (laser aperture) down for safety and

continue tightening end cap until laser flare is switched on (visible

through protective front cap). Remove protective plastic cap on

front end of unit. Turn sight ring until it is aligned with vertical laser

line. Your Rescue Laser

is ready for use.

™

3. Ensure Rescue Laser

emergency signaling device is secured so it

™

cannot be lost. Use the hole in the end cap to secure with a tether or

lanyard.

4. To turn Rescue Laser

off, point the light output end ( laser aperture )

™

down for safety and twist then unscrew back end cap until the laser is

off, plus one more turn. Replace protective cap

to keep lens clean.

Signaling (a) *

Aim Rescue Laser

emergency signaling device in

™

the direction of the target ( aircraft, boat, vehicle,

rescue party ) you wish to signal. With the laser line

vertical ( up and down ), point laser aperture

toward the target. Make a "V" with your

outstretched hand over the intended target. With

the signaling device held near your eye in line of

sight, very slowly scan the vertical laser back and

forth between your fingers toward the target

making each finger red as you scan and line up

target through the sight ring.

Important

: Always point the laser output end away from your eyes.

Keep signaling until you have positive contact with your rescuers or target

and they are able to see you without the use of the signaling device.

*Signals up to 20 miles away. Testing conducted

with the naked eye, on a clear moonless night with

no background or environmental lighting. The

effectiveness of any signaling device may be

compromised by actual environmetal conditions.

Detecting (b)

When looking for reflective materials, point the

laser aperture toward the object you are scanning

and hold the laser near your line of sight to see the

return flash from the object.

Safety Summary

Caution: use of controls or adjustments, or performance of procedures

other than those specified herein may result in hazardous radiation

exposure.

This laser process machine is certified as a Class IIIa laser product to the

requirements of the US Federal product performance standard for laser

products contained in the regulations in 21 CFR sub-chapter J.

(a)

(b)

Rescue Laser Flare

Magnum signaling device

End Cap

This device should only be used to signal persons at a distance greater

than 13 feet (4 meters).

During the performance of routine maintenance procedures such as

cleaning the exterior or changing batteries the power should be turned to

the off position.

Under no circumstance shall attempts be made to disassemble or service

this product. All service is to be performed by the manufacturer or their

authorized agent.

AVOID DIRECT EYE EXPOSURE TO THE BEAM

Battery Replacement and Maintenance

Battery replacement and exterior cleaning are the only maintenance

required. There are no user serviceable components inside the device.

Attempting to gain access to the laser components will void the warranty.

Turn laser off before changing batteries or cleaning. The Rescue Laser

Flare

Magnum operates on two 1.5-volt alkaline AA batteries. To replace

the batteries, turn laser off, unscrew end cap and remove batteries. Insert

two fresh batteries as shown in the diagram above with the positive (+)

end facing toward the end cap, then screw on end cap. Tighten end cap

until laser light is switched on (visible through protective front plastic cap),

then unscrew until light is off, plus one more turn. For optimum perfor-

mance, the batteries in your

Rescue Laser

once every year.

Lens may be cleaned with a soft dry cloth or camera lens brush. Do not

use cleaning fluids. Exterior may be wiped with a damp cloth to remove

surface dirt, then dried.

Troubleshooting

1. Rescue Laser

emergency signaling device does not turn on or stay

™

on, verify battery has been inserted with the positive end facing outward

as shown in diagram above. Check contact between the battery and the

end cap. Any corrosion formed by a foreign substance should be

carefully removed.

2. Laser light failure — verify two fresh 1.5-volt AA batteries have been

properly inserted with the positive end facing outward as shown in the

diagram above, if necessary, replace batteries.

3. If the above steps have been followed and the

emergency signaling device still does not perform properly, follow the

steps in the how and when to make a warranty claim, or contact

our warranty and repair facility: 1. 907.245.4475. Limited Lifetime

Warranty and online registration available at www.greatlandlaser.com

It is illegal to point this device at an

L ASER APE RT U R E

aircraft except in an emergency!

Greatland Laser

Ranch Cucamonga, CA, USA

Model: Rescue Laser Flare

Magnum

Manufactured:

2022

2023 2024

11 12

H02501

Serial Number: RLFAA024-01

Laser Aperture with

Protective Cover

Warning & Certification Label

Two 1.5-volt AA batteries

should be replaced at least

™

Rescue Laser

™

Greatland Laser LLC

PO Box 792

Willow, Alaska 99688 USA

Toll-Free: 866.889.3425