- ページ 2

懐中電灯 Greatland Laser Rescue Laser Flare GLF032-01のPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。Greatland Laser Rescue Laser Flare GLF032-01 2 ページ。

ページを印刷する

Assembly and Operation

1. To assemble, unscrew end cap. Insert

and then screw on end cap.

2. Point the light output end (laser aperture) down for safety and

continue tightening end cap until laser flare is switched on (visible

through protective front cap). Remove protective plastic cap on

front end of unit. Turn sight ring until it is aligned with vertical laser

line. Your Rescue Laser

is ready for use.

3. Ensure Rescue Laser

emergency signaling device is secured so it

cannot be lost. Use the hole in the end cap to secure with a tether or

lanyard.

4. To turn Rescue Laser

off, point the light output end ( laser aperture )

down for safety and twist then unscrew back end cap until the laser is

off, plus one more turn. Replace protective cap

to keep lens clean.

Signaling (a) *

Aim Rescue Laser

emergency signaling device in

the direction of the target ( aircraft, boat, vehicle,

rescue party ) you wish to signal. With the laser line

vertical ( up and down ), point laser aperture

toward the target. Make a "V" with your

outstretched hand over the intended target. With

the signaling device held near your eye in line of

sight, very slowly scan the vertical laser back and

forth between your fingers toward the target

making each finger red as you scan and line up

target through the sight ring.

Important

: Always point the laser output end away from your eyes.

Keep signaling until you have positive contact with your rescuers or target

and they are able to see you without the use of the signaling device.

*Signals up to 30 miles away. Testing conducted

with the naked eye, on a clear moonless night with

no background or environmental lighting. The

effectiveness of any signaling device may be

compromised by actual environmetal conditions.

Detecting (b)

When looking for reflective materials, point the

laser aperture toward the object you are scanning

and hold the laser near your line of sight to see the

return flash from the object.

Safety Summary

Caution: use of controls or adjustments, or performance of procedures

other than those specified herein may result in hazardous radiation

exposure.

This laser process machine is certified as a Class IIIa laser product to the

requirements of the US Federal product performance standard for laser

products contained in the regulations in 21 CFR sub-chapter J.

one CR123, 3V lithium battery

(a)

(b)

Rescue Laser Flare

Green signaling device

End cap with

lanyard hole

Twist to Turn

On /Off

This device should only be used to signal persons at a distance greater

than 13 feet (4 meters).

During the performance of routine maintenance procedures such as

cleaning the exterior or changing batteries the power should be turned to

the off position.

Under no circumstance shall attempts be made to disassemble or service

this product. All service is to be performed by the manufacturer or their

authorized agent.

AVOID DIRECT EYE EXPOSURE TO THE BEAM

Battery Replacement and Maintenance

Battery replacement and exterior cleaning are the only maintenance

required. There are no user serviceable components inside the device.

Attempting to gain access to the laser components will void the warranty.

Turn laser off before changing batteries or cleaning. The Rescue Laser

Flare

Green operates on one CR123, 3V lithium battery. To replace, turn

laser off, unscrew end cap and remove battery. Insert one fresh battery as

shown in the diagram above with the positive (+) end facing toward the

end cap, then screw on end cap. Tighten end cap until laser light is

switched on (visible through protective front plastic cap), then unscrew

until light is off, plus one more turn. For optimum performance, the battery

in your

Rescue Laser

should be replaced at least once every year.

Lens may be cleaned with a soft dry cloth or camera lens brush. Do not

use cleaning fluids. Exterior may be wiped with a damp cloth to remove

surface dirt, then dried.

Troubleshooting

Rescue Laser

emergency signaling device does not turn on or stay

on, verify battery has been inserted with the positive end facing outward

as shown in diagram above. Check contact between the battery and the

end cap. Any corrosion formed by a foreign substance should be

carefully removed.

2. Laser light failure — verify one CR123, 3V lithium battery has been

properly inserted with the positive end facing outward as shown in the

diagram above, if necessary, replace battery.

3. If the above steps have been followed and the

emergency signaling device still does not perform properly, follow the

steps in the how and when to make a warranty claim, or contact

our warranty and repair facility: 1. 907.245.4475. 180 Day Warranty,

see website for online registration available at www.greatlandlaser.com

It is illegal to point this device at an

L ASER APE RT U R E

aircraft except in an emergency!

Greatland Laser

Ranch Cucamonga, CA, USA

Model: Rescue Laser Flare

Green

Manufactured:

2023

2024 2025

11 12

H002380

Serial Number: GLF032-01

Certification and Warning label

Laser Aperture

3-Volt lithium battery ± polarity

Rescue Laser

Greatland Laser LLC

PO Box 792

Willow, Alaska 99688 USA

Toll-Free: 866.889.3425